Introduction
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your Danco 89205 Tub Spout Diverter Repair Kit. This kit is designed to repair the diverter mechanism in most standard tub spouts, offering a practical solution for leaky or malfunctioning diverters. The kit includes a stem, gate, and diverter gasket, constructed from durable metal and plastic components with a chrome finish to ensure longevity and compatibility with existing fixtures.
Safety Information
- Always turn off the main water supply to your bathroom before beginning any plumbing work to prevent water damage.
- Wear appropriate personal protective equipment, such as safety glasses and gloves, to protect against potential hazards.
- Ensure all connections are secure to prevent leaks. Do not overtighten components, as this can cause damage.
- If you are unsure about any step, consult a qualified plumber.
Package Contents
Verify that all components are present in your Danco 89205 Tub Spout Diverter Repair Kit:
- 1 x Diverter Stem (Chrome finish)
- 1 x Diverter Gate (Plastic)
- 1 x Diverter Gasket (Rubber)
Image: Components of the Danco 89205 Tub Spout Diverter Repair Kit, including the chrome stem, black rubber gasket, and white plastic gate.
Setup and Installation
Follow these steps to install the Danco 89205 Tub Spout Diverter Repair Kit:
- Turn Off Water Supply: Locate the main water shut-off valve for your home or bathroom and turn it off. Open the tub faucet to drain any remaining water.
- Remove Existing Tub Spout: Depending on your tub spout type, it will either be threaded on or held by a set screw. Unscrew threaded spouts counter-clockwise. For set screw spouts, loosen the screw (usually on the underside) with an Allen wrench or screwdriver and pull the spout off.
- Access Diverter Mechanism: Once the tub spout is removed, you will gain access to the internal diverter mechanism. Carefully remove the old diverter stem, gate, and gasket. Note their orientation for reference.
- Clean the Spout Interior: Clean any mineral deposits or debris from the inside of the tub spout where the diverter components reside.
- Install New Gasket and Gate: Place the new diverter gasket into its designated position within the tub spout. Then, insert the new diverter gate, ensuring it is correctly seated.
- Install New Diverter Stem: Insert the new chrome diverter stem into the spout, aligning it with the gate and gasket. Ensure it moves freely up and down.
Image: The chrome diverter stem and rubber gasket, key components for installation.
- Reattach Tub Spout: Slide the tub spout back onto the pipe. If it's a set screw type, tighten the screw. If it's threaded, screw it on clockwise until snug. Do not overtighten.
- Restore Water Supply: Slowly turn the main water supply back on. Check for any leaks around the tub spout.
- Test Diverter: Turn on the tub faucet and pull up the diverter stem to check if water is properly redirected to the showerhead. Push it down to ensure water flows from the tub spout.
Operation
To operate the tub spout diverter:
- For Tub Flow: Ensure the diverter stem is in the down position. Water will flow directly from the tub spout.
- For Shower Flow: While water is flowing from the tub spout, pull the diverter stem upwards. This will redirect the water flow to the showerhead.
- To Return to Tub Flow: Push the diverter stem back down. Water will resume flowing from the tub spout.
Maintenance
Regular maintenance helps ensure the longevity and proper function of your diverter repair kit:
- Cleaning: Periodically clean the exterior of the diverter stem with a soft cloth and mild, non-abrasive cleaner to maintain its chrome finish. Avoid harsh chemicals that can damage the finish or rubber components.
- Check for Leaks: Regularly inspect the area around the tub spout for any signs of leaks. Address minor leaks promptly to prevent further damage.
- Smooth Operation: If the diverter stem becomes stiff or difficult to operate, it may indicate mineral buildup or wear. Consider disassembling and cleaning the components, or replacing them if necessary.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from tub spout when diverter is engaged. | Worn or improperly seated gasket/gate; debris obstructing seal. | Ensure gasket and gate are correctly installed. Clean any debris. Replace components if worn. |
| Diverter stem is stiff or difficult to pull/push. | Mineral buildup; lack of lubrication; damaged stem. | Disassemble and clean components. Apply plumber's grease to moving parts. Replace if damaged. |
| No water or low flow to showerhead when diverter is engaged. | Diverter not fully engaging; obstruction in showerhead or pipe. | Check diverter stem for full travel. Clean showerhead. Inspect internal spout for obstructions. |
Specifications
- Model Number: 89205
- Brand: Danco
- Material: Metal (Stem), Plastic (Gate), Rubber (Gasket)
- Finish Type: Chrome
- Included Components: (1) stem, (1) gate, and (1) diverter gasket
- Universal Design: Fits most standard tub spouts
- Item Weight: 0.05 Pounds
- UPC: 037155892051
Warranty Information
This Danco product includes a manufacturer's warranty. For specific details regarding warranty coverage, duration, and claims process, please refer to the documentation included with your purchase or visit the official Danco website. Retain your proof of purchase for warranty purposes.
Customer Support
If you encounter any issues or have questions regarding the Danco 89205 Tub Spout Diverter Repair Kit that are not covered in this manual, please contact Danco customer support. You can typically find contact information, including phone numbers and email addresses, on the official Danco website or on the product packaging.