1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Bio Bidet ELITE3 Freshwater Spray Bidet Attachment. Please read this manual thoroughly before installation and use to ensure proper function and safety. The ELITE3 is designed to provide a comfortable and hygienic personal wash experience with adjustable water pressure and dual nozzles.
Image 1.1: Bio Bidet ELITE3 Bidet Attachment installed on a toilet.
2. Safety Information
- Ensure all connections are tightened properly to prevent leaks. Do not overtighten.
- Use only cold water supply. This unit is not designed for hot water connection.
- Do not use abrasive cleaners or harsh chemicals on the bidet attachment, as this may damage the finish or internal components.
- Keep out of reach of children.
- If any part is damaged or missing, do not attempt to install or operate the unit. Contact customer support.
3. Package Contents
Verify that all components are present before beginning installation:
- Bio Bidet ELITE3 Bidet Attachment
- Metal Braided Water Supply Hose
- T-Adapter Valve
- Mounting Plates and Bolts
- Rubber Washers
- Installation Manual (this document)
Image 3.1: Included metal braided water supply hose and T-adapter valve.
4. Installation Guide
Installation typically takes about 15 minutes and requires no special tools or electricity. You may need a wrench for tightening connections.
4.1. Preparation
- Turn off the water supply valve to your toilet.
- Flush the toilet to drain the tank completely.
- Disconnect the existing water supply hose from the toilet tank. Have a small towel ready to catch any residual water.
4.2. Attaching the T-Adapter
- Install the T-adapter valve to the fill valve on the bottom of your toilet tank. Ensure the rubber washer is properly seated.
- Connect your toilet's original water supply hose to the bottom of the T-adapter.
4.3. Installing the Bidet Attachment
- Remove your toilet seat. Place the bidet attachment on the toilet rim, aligning the mounting holes with those on your toilet.
- Place your toilet seat back on top of the bidet attachment and secure it using the original toilet seat bolts. Adjust the bidet attachment forward or backward as needed for optimal fit.
- Connect one end of the provided metal braided water supply hose to the side of the T-adapter.
- Connect the other end of the metal braided water supply hose to the water inlet on the bidet attachment.
Image 4.1: Connecting the water supply hose to the bidet attachment.
4.4. Final Steps
- Slowly turn on the main water supply valve to your toilet.
- Check all connections for leaks. If leaks occur, tighten the connections slightly. Do not overtighten.
Your Bio Bidet ELITE3 is now ready for use.
Installation Video
Video 4.1: General installation guide for bidet attachments. This video demonstrates the typical steps for installing a bidet attachment to a toilet.
5. Operating Instructions
The ELITE3 features two control knobs for easy operation.
Image 5.1: Control panel with water pressure and nozzle selection knobs.
5.1. Water Pressure Control
- The top knob controls the water pressure. Turn it clockwise to increase pressure and counter-clockwise to decrease pressure.
- Start with the lowest pressure setting and gradually increase to your desired comfort level.
- Turn the knob to the 'OFF' position to stop the water flow.
5.2. Nozzle Selection and Cleaning
- The bottom knob allows you to select the desired wash function: Posterior Wash (for rear cleansing) or Feminine Wash (for front cleansing).
- To activate the self-cleaning function for the nozzles, turn the knob to the 'NOZZLE CLEANING' position. Water will spray to rinse the nozzles.
Image 5.2: Dual retractable nozzles for posterior and feminine wash.
Operation Video
Video 5.1: Demonstration of bidet attachment features and operation. This video illustrates how to use the control knobs for different wash functions.
6. Maintenance
6.1. Cleaning the Bidet
- Regularly wipe down the exterior of the bidet attachment with a soft, damp cloth and mild soap.
- Do not use harsh detergents, abrasive cleaners, or brushes, as these can scratch the surface.
6.2. Nozzle Cleaning
- Use the built-in 'NOZZLE CLEANING' function on the control knob for a quick rinse of the nozzles.
- For a more thorough cleaning, gently pull out the nozzles and clean them with a soft brush and mild soap. Ensure they retract properly after cleaning.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaks from connections | Loose connections, missing or improperly seated washers | Ensure all connections are hand-tightened, then use a wrench for a quarter turn. Check that rubber washers are correctly placed. Do not overtighten. |
| No water spray or weak spray | Water supply valve closed, low water pressure, clogged nozzle | Ensure the toilet's water supply valve is fully open. Check household water pressure. Clean the nozzles using the self-cleaning function or manually. |
| Nozzles do not retract | Debris, obstruction, or damage | Check for any visible obstructions around the nozzles. Clean the nozzles thoroughly. If the issue persists, contact customer support. |
| Toilet seat is not level | Bidet attachment not properly aligned | Adjust the bidet attachment's position on the toilet rim and ensure the toilet seat bolts are tightened evenly. |
8. Specifications
- Model: Elite3
- Dimensions: 9 x 19 x 4 inches (Product), 17 1/4 x 8 inches (Size)
- Item Weight: 2.89 pounds
- Material: Brass (valve), Quality ABS Resin
- Color: White
- Power Source: Non-electric (operates on water pressure)
- Nozzles: Dual, Retractable, Self-cleaning
- Water Pressure Control: Adjustable knob
Image 8.1: Dimensional drawing of the Bio Bidet ELITE3.
Image 8.2: Diagram illustrating the internal brass flow valve for durability and precise flow control.
9. Warranty & Support
9.1. Warranty Information
The manufacturer warranty covers customer purchases in the USA and Canada for 1 year from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
9.2. Customer Support
For technical assistance, warranty claims, or any questions regarding your Bio Bidet ELITE3, please contact our customer care:
Customer Care Number: 877.339.5214
Please have your model number (Elite3) and date of purchase available when contacting support.
