1. Introduction
This manual provides comprehensive instructions for the safe and efficient installation, operation, and maintenance of the Hammond Manufacturing 1472-36 N12 Console Cabinet. Please read this manual thoroughly before proceeding with any installation or operation.
The Hammond 1472-36 is a robust NEMA Type 12 console cabinet designed for industrial applications, offering protection for sensitive electronic equipment in environments where dust, dirt, and light splashing liquids may be present. Its durable construction ensures long-term reliability.
2. Safety Information
Always observe local electrical codes and safety regulations. Ensure power is disconnected before performing any installation or maintenance. Only qualified personnel should perform electrical connections.
- Do not operate the cabinet if it is damaged.
- Ensure proper grounding.
- Avoid overloading the cabinet with excessive weight.
- Keep ventilation openings clear.
3. Product Overview
Figure 3.1: Front view of the Hammond 1472-36 N12 Console Cabinet. This image shows the grey industrial cabinet with a hinged front door and a sloped top surface, designed for housing control equipment.
The 1472-36 N12 Console Cabinet features a robust steel construction with a grey finish, designed to protect internal components from dust, dirt, and light splashing water. It includes a hinged door for easy access and a sloped top for ergonomic control panel mounting.
4. Setup and Installation
4.1 Unpacking
Carefully unpack the console cabinet. Inspect for any shipping damage. Report any damage to the carrier immediately. Retain all packaging materials until the unit is confirmed to be in working order.
4.2 Mounting
The cabinet is designed for floor mounting. Ensure the mounting surface is level and capable of supporting the cabinet's weight (approximately 190 lbs) plus the weight of any installed equipment. Use appropriate anchor bolts (not supplied) for secure installation.
- Position the cabinet in the desired location.
- Mark the drilling points for the mounting feet.
- Drill holes and install appropriate anchors.
- Secure the cabinet using bolts, ensuring it is level and stable.
4.3 Internal Component Installation
Install internal components such as control panels, electrical devices, and wiring according to their respective manufacturer's instructions. Ensure proper cable management and ventilation within the cabinet.
5. Operating Instructions
The Hammond 1472-36 is a passive enclosure. Its operation is dependent on the equipment installed within it. Ensure all internal equipment is properly connected and configured according to its own operational guidelines.
- Ensure the cabinet door is securely latched to maintain NEMA 12 protection.
- Regularly check for any obstructions to ventilation.
- Do not place heavy objects on the sloped top surface that could impede access or damage the cabinet.
6. Maintenance
6.1 Cleaning
Clean the exterior of the cabinet with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish. For stubborn dirt, a mild detergent can be used.
6.2 Inspection
Periodically inspect the cabinet for signs of wear, corrosion, or damage. Check door hinges and latches for proper function. Ensure all mounting bolts remain tight.
6.3 Gasket Maintenance
The NEMA 12 rating relies on the integrity of the door gasket. Inspect the gasket for cracks, tears, or compression set. Replace if necessary to maintain environmental protection.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Door not closing securely | Misaligned hinges or latch; obstructed gasket | Adjust hinges/latch; clear any obstructions from gasket area. |
| Cabinet unstable after mounting | Uneven mounting surface; loose anchor bolts | Ensure surface is level; tighten all anchor bolts. |
| Internal equipment overheating | Poor ventilation; overloaded equipment | Ensure ventilation openings are clear; consider adding cooling solutions if necessary. |
8. Specifications
- Model: 1472-36
- Type: N12 Console Cabinet
- Material: Steel
- Weight: Approximately 190 lbs (86.2 kg)
- Environmental Rating: NEMA Type 12 (Dust, dirt, and light splashing liquids)
- Manufacturer: Hammond Manufacturing
9. Warranty and Support
For specific warranty information, please refer to the documentation provided by Hammond Manufacturing at the time of purchase or visit their official website. For technical support, please contact Hammond Manufacturing directly through their customer service channels.
Contact Information:
- Website: www.hammfg.com
- Customer Service: Refer to website for regional contact details.
