Chamberlain Model #1573 Garage Door Remote Control User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, programming, operation, and maintenance of your Chamberlain Model #1573 Garage Door Remote Control. Please read this manual thoroughly before using the device to ensure proper function and safety. This remote control is designed to operate compatible Chamberlain and LiftMaster garage door openers.

2. Safety Information

Always observe the following safety precautions to reduce the risk of injury or damage:

• Keep remote controls out of reach of children.
• Operate the garage door only when it is in full view and free of obstructions.
• Never allow children to play with the garage door opener or remote control.
• Ensure the garage door is fully closed before leaving the premises.
• Dispose of batteries properly according to local regulations.

3. Product Overview

The Chamberlain Model #1573 is a compact and ergonomic garage door remote control designed for ease of use. It features multiple buttons for controlling your garage door opener.

Figure 1: Front view of the Chamberlain Model #1573 remote control. The remote is black with the "CHAMBERLAIN" logo and a circular signal icon in gold on the upper left. Below this are three distinct, rectangular control buttons.

Figure 2: Back view of the Chamberlain Model #1573 remote control. This side displays regulatory information including IC: 2666A, FCC ID: HBW1573, and the part number 41A6127-1. It also indicates "ASSEMBLED IN MEXICO" and includes a metal clip for attachment.

4. Setup & Programming

4.1. Battery Installation

The Chamberlain Model #1573 remote control requires AA or AAA batteries. To install or replace batteries:

1. Locate the battery compartment cover on the back of the remote.
2. Remove the cover by sliding it off or unscrewing it, depending on the design.
3. Insert new AA or AAA batteries, ensuring correct polarity (+/-).
4. Replace the battery compartment cover securely.

4.2. Programming the Remote Control

To program your remote control to your garage door opener, follow these general steps. Specific steps may vary slightly depending on your garage door opener model. Refer to your garage door opener's manual for detailed instructions if needed.

1. Locate the Learn Button: On your garage door opener motor unit, locate the "Learn" button. This button is usually on the back or side panel of the motor unit, often near the antenna wire. The color of the learn button (e.g., red, purple, yellow, green) may indicate the frequency or technology of your opener.
2. Press the Learn Button: Press and immediately release the "Learn" button on the garage door opener. The learn indicator light will glow steadily for 30 seconds.
3. Press the Remote Button: Within 30 seconds, press and hold the button on your Chamberlain remote control that you wish to use to operate the garage door.
4. Release the Remote Button: Release the remote control button when the garage door opener lights flash or two clicks are heard. This indicates that the remote has been successfully programmed.
5. Test the Remote: Press the programmed button on your remote control to test its operation. The garage door should activate.

If the remote does not work, repeat the programming steps. Ensure you are within range of the garage door opener during programming.

5. Operating Instructions

Once programmed, operating your Chamberlain Model #1573 remote control is straightforward:

• To Open or Close the Garage Door: Press the programmed button on your remote control. The garage door will begin to move.
• To Stop the Garage Door: Press the programmed button again while the door is in motion. The door will stop.
• To Reverse the Garage Door: If the door is stopped mid-travel, pressing the button again will reverse its direction.

Ensure a clear line of sight to the garage door and that no obstructions are present before operating.

6. Maintenance

6.1. Battery Replacement

If the remote control's range decreases significantly or it stops responding, the batteries may need replacement. Refer to section 4.1 for battery installation instructions. The remote uses AA or AAA batteries.

6.2. Cleaning

Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing or internal components.

7. Troubleshooting

8. Specifications

• Model Number: #1573
• Part Number: Chamberlain Group, Inc. Chamber Remote Controller IC:2666A #1573 FCC ID:#HBW1573 (Assembled In Mexico 41A6127-1)
• Brand: CHAMBERLAIN
• Item Weight: 2.39 ounces
• Package Dimensions: 5.12 x 2.76 x 1.93 inches
• Special Feature: Ergonomic
• Batteries Required: Yes (AA or AAA batteries)
• Max Number of Supported Devices: 1
• Compatible Devices: Garage Door Openers
• Connectivity Technology: Radio Frequency
• FCC ID: HBW1573
• IC: 2666A

9. Warranty & Support

For warranty information or technical support, please refer to the official Chamberlain website or contact Chamberlain customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

Online Support: www.chamberlain.com/support

Phone Support: Refer to the Chamberlain website for regional contact numbers.

10. Regulatory Information

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: HBW1573.

Industry Canada (IC) Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. IC: 2666A.