Pronomic Stage XFXM-20 Microphone Cable User Manual

1. Introduction

This manual provides essential information for the proper use, setup, and maintenance of your Pronomic Stage XFXM-20 Microphone Cable. This professional, balanced audio cable is designed for reliable audio transmission in various applications, including microphone connections and home studio wiring. It features durable components and oxygen-free copper for clear signal integrity.

2. Safety Information

• Do not expose the cable to extreme temperatures, direct sunlight, or excessive moisture.
• Avoid sharp bends, kinks, or crushing the cable, as this can damage internal conductors.
• Ensure connectors are clean and free from debris before connecting to equipment.
• Always grasp the connector housing, not the cable itself, when plugging or unplugging.
• Keep the cable away from sources of strong electromagnetic interference if possible.

3. Product Overview

The Pronomic Stage XFXM-20 is a high-quality XLR cable featuring a 3-pin female XLR connector on one end and a 3-pin male XLR connector on the other. It is constructed with oxygen-free copper for optimal signal transfer and a high-density copper shield to protect against noise. The robust outer sheath and hand-soldered connectors with chuck-type strain relief ensure durability.

Image 3.1: The Pronomic Stage XFXM-20 Microphone Cable, showing both the 3-pin male and 3-pin female XLR connectors.

Image 3.2: A close-up view of the Pronomic XLR connector, highlighting the robust strain relief and brand marking.

Image 3.3: An exploded view of the XLR connector, illustrating the internal wiring and components for secure signal transmission.

4. Setup

Connecting your Pronomic Stage XFXM-20 cable is straightforward:

1. Identify Connectors: Locate the 3-pin male XLR connector (with pins) and the 3-pin female XLR connector (with holes).
2. Connect to Microphone/Input: Plug the 3-pin female XLR connector into the corresponding male XLR output port on your microphone or other audio source. Ensure it clicks securely into place.
3. Connect to Mixer/Output: Plug the 3-pin male XLR connector into the corresponding female XLR input port on your mixer, audio interface, or other receiving equipment. Ensure it clicks securely into place.
4. Cable Routing: Route the cable safely to avoid tripping hazards and minimize interference from power cables or other electronic devices.

5. Operating

Once connected, the Pronomic Stage XFXM-20 cable facilitates balanced audio signal transfer. No specific operational steps are required for the cable itself beyond ensuring secure connections and proper routing.

• Verify all connections are firm before operating audio equipment.
• Avoid excessive tension or pulling on the cable during use.
• To disconnect, press the release tab on the XLR connector (if present) and gently pull the connector housing.

6. Maintenance

Proper maintenance extends the life of your cable:

• Cleaning: Wipe the cable and connectors with a soft, dry cloth to remove dust and dirt. Do not use harsh chemicals or abrasive cleaners.
• Storage: When not in use, coil the cable loosely in a figure-eight pattern to prevent kinks and tangles. Secure with a cable tie or hook-and-loop fastener. Store in a cool, dry place.
• Inspection: Periodically inspect the cable for any signs of damage, such as cuts in the outer sheath, bent pins on connectors, or loose connections.

7. Troubleshooting

If you experience issues with your audio setup, consider the following:

• No Sound:
  • Ensure both ends of the cable are securely connected.
  • Verify that the microphone and receiving equipment are powered on and functioning correctly.
  • Test with a different cable if available to rule out cable failure.
• Humming or Buzzing Noise:
  • Check if the cable is routed too close to power cables or other electrical devices that may cause interference.
  • Ensure the cable's connectors are fully inserted and making good contact.
  • Verify that all equipment in the audio chain is properly grounded.
• Intermittent Signal:
  • Inspect connectors for bent pins or loose parts.
  • Ensure the cable is not being stressed or pulled during use.

8. Specifications

9. Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Pronomic customer service directly. Keep your proof of purchase for any warranty claims.