RABALUX 2322

Download PDF
Contents

Rabalux 2322 Bath Under-Cabinet Light Instruction Manual

Model: 2322

1. Introduction

The Rabalux 2322 Bath Under-Cabinet Light is designed to provide efficient illumination and convenient power access in indoor environments. Its white finish integrates discreetly into various interior styles. This manual provides essential information for safe installation, operation, and maintenance of your Rabalux 2322 under-cabinet light.

Please read these instructions carefully before installation and use, and retain them for future reference.

Rabalux 2322 Bath Under-Cabinet Light with integrated switch and two power outlets

Image 1.1: Front view of the Rabalux 2322 Under-Cabinet Light, showing the integrated fluorescent tube, power switch, and two electrical outlets on the right side.

2. Safety Instructions

To ensure safe operation and prevent damage, observe the following safety guidelines:

  • Indoor Use Only: This product is designed exclusively for indoor use in enclosed spaces.
  • Power Disconnection: Always disconnect the main power supply before performing any installation, maintenance, cleaning, or lamp replacement.
  • IP20 Rating: The fixture has an IP20 protection rating, meaning it is protected against solid objects larger than 12.5mm but has no protection against water. Do not install in areas where direct water contact or high humidity is present, despite the "Bath" designation which refers to style, not water resistance.
  • Professional Installation: If you are not confident with electrical installations, consult a qualified electrician.
  • Voltage: Ensure the power supply voltage matches the product's requirements (230 Volt).
  • Lamp Type: Use only the specified lamp type (G13 T8 15W) for replacement.
  • Ventilation: Ensure adequate ventilation around the fixture to prevent overheating.
  • Cleaning: Do not use abrasive or corrosive cleaning agents.

3. Package Contents

Verify that all components are present and undamaged:

  • 1 x Rabalux 2322 Under-Cabinet Light fixture
  • 1 x T8 15W Fluorescent Tube (950 lm; 2700 K)
  • Mounting hardware (screws, anchors)
  • Instruction Manual

Note: A connection cable for power supply is not included and must be provided separately.

4. Setup and Installation

The Rabalux 2322 is designed for recessed mounting under cabinets or shelves. Follow these steps for installation:

  1. Preparation: Ensure the main power supply to the installation area is switched off at the circuit breaker.
  2. Mounting Location: Select a suitable, stable surface under a cabinet or shelf. Consider the dimensions of the fixture (60.5 cm length, 6.5 cm height, 8.5 cm depth) to ensure proper fit and clearance.
  3. Marking: Use the fixture as a template to mark the drilling points for the mounting hardware.
  4. Drilling: Drill pilot holes at the marked locations. Insert wall anchors if necessary.
  5. Wiring: Connect the power supply cable (not included) to the terminal block inside the fixture. Ensure correct polarity (Live, Neutral, Earth) according to local electrical codes. The fixture is designed for AC power (230V).
  6. Mounting the Fixture: Secure the fixture to the mounting surface using the provided screws.
  7. Lamp Installation: Carefully insert the T8 fluorescent tube into the G13 sockets. Ensure it is seated correctly.
  8. Final Check: Double-check all connections and ensure the fixture is securely mounted.
  9. Power On: Restore power at the circuit breaker.
Rabalux 2322 Bath Under-Cabinet Light with dimensions: 605mm length, 65mm height, 85mm depth

Image 4.1: Dimensional drawing of the Rabalux 2322 Under-Cabinet Light, indicating a length of 605mm, a height of 65mm, and a depth of 85mm.

5. Operating Instructions

The Rabalux 2322 Under-Cabinet Light is straightforward to operate:

  • Light Operation: Use the integrated switch located on the right side of the fixture to turn the light ON or OFF.
  • Power Outlets: The two integrated power outlets can be used to connect small electrical appliances. Ensure the total wattage of connected devices does not exceed the fixture's maximum capacity.
  • Warm-up Time: Fluorescent lamps may require a few seconds to reach full brightness after being switched on. This is normal operation.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your light fixture:

  • Cleaning: Disconnect power before cleaning. Wipe the fixture with a soft, dry, or slightly damp cloth. Do not use harsh chemicals, abrasive cleaners, or solvents.
  • Lamp Replacement:
    1. Switch off the power supply at the main circuit breaker.
    2. Allow the lamp to cool down if it has been recently in use.
    3. Carefully remove the old T8 fluorescent tube from its G13 sockets.
    4. Insert a new G13 T8 15W fluorescent tube, ensuring it is securely seated.
    5. Restore power.
  • Inspection: Periodically check the fixture for any signs of damage, loose connections, or wear. If any issues are found, disconnect power and address them immediately.

7. Troubleshooting

If you encounter problems with your Rabalux 2322 light, refer to the following common issues and solutions:

ProblemPossible CauseSolution
Light does not turn on.No power supply.
Faulty lamp.
Loose connection.
Check the main power supply and circuit breaker.
Ensure the integrated switch is ON.
Replace the fluorescent tube.
Verify all electrical connections (with power off).
Light flickers or is dim.Aging lamp.
Incorrect lamp type.
Replace the fluorescent tube.
Ensure a G13 T8 15W lamp is used.
Integrated outlets are not working.No power supply to the fixture.
Overload.
Check the main power supply.
Reduce the load on the outlets.
Unusual noise or smell.Electrical fault.Immediately disconnect power. Do not use the fixture. Contact a qualified electrician.

If the problem persists after attempting these solutions, consult a qualified electrician or contact Rabalux customer support.

8. Specifications

BrandRABALUX
Model Number2322
Product Dimensions (L x W x H)60.5 cm x 8.51 cm x 6.5 cm
Weight800 g
MaterialPlastic, Metal
ColorWhite
Voltage230 Volt (AC)
Max. Compatible Wattage15 Watt
Lamp TypeG13 T8 Fluorescent Tube
Luminous Flux950 Lumen
Color Temperature2700 Kelvin
Average Lifespan12000 Hours
Energy Efficiency ClassB
IP RatingIP20
Special FeaturesIntegrated switch and 2 power outlets
Installation TypeRecessed mounting
Specific UseFor use in enclosed indoor spaces only

9. Warranty and Support

Warranty: For detailed warranty information, please refer to the terms and conditions provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.

Support: If you require technical assistance or have questions not covered in this manual, please contact Rabalux customer service through their official website or the contact information provided with your product.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.