Introduction
This manual provides instructions for the installation, operation, and maintenance of the Morris 85221 Decorative Dual F Connector Wall Plate. This product is designed to provide a clean and organized connection point for two F-type coaxial cables, commonly used for cable television, satellite, or antenna signals. Please read these instructions carefully before installation to ensure proper and safe use.
Important Safety Information
WARNING: Always disconnect power to the circuit at the main service panel before installing or servicing electrical components. Failure to do so may result in serious injury or death.
- Ensure all connections are secure to prevent signal loss or electrical hazards.
- Do not install in wet or damp locations unless specifically rated for such environments.
- This product is intended for low-voltage coaxial cable applications. Do not connect to AC power lines.
- If you are unsure about any part of the installation process, consult a qualified electrician or technician.
Package Contents
Verify that all components are present before beginning installation:
- 1 x Decorative Wall Plate (White)
- 1 x Dual F-Connector Jack Insert
- 2 x Mounting Screws (typically included with wall plates)
Note: Coaxial cables and tools for installation are sold separately.
Product Features
- Two-Piece Design: The wall plate and F-connector jack are separate pieces, allowing for easier installation and removal for maintenance or painting without disconnecting cables.
- Dual F-Connectors: Provides two F-type coaxial connections for multiple devices or lines.
- Decorative Finish: Flush design in white plastic for a clean aesthetic.
- Durable Material: Constructed from UL94V-0 Flame Retardant Plastic for safety.
- High-Quality Connectors: Features 50 Micro Inches of Gold Plating for optimal signal integrity.
- Compliance: Meets FCC Requirements and complies with UL Standard 1863 and Article 800-51 of The National Electrical Code. UL/CSA Listed.
Specifications
| Model Number | 85221 |
| Brand | Morris |
| Material | UL94V-0 Flame Retardant Plastic |
| Color | White |
| Connector Type | F-Type Coaxial |
| Configuration | Dual |
| Plating | 50 Micro Inches of Gold |
| Certifications | FCC Compliant, UL Standard 1863, Article 800-51 of The National Electrical Code, UL/CSA Listed |
Image: The Morris 85221 Dual F Connector Wall Plate shown with approximate dimensions (4.7 inches / 11 cm in height) for reference during installation planning.
Installation Instructions
This section outlines the steps for installing your Morris 85221 Decorative Dual F Connector Wall Plate. Basic tools are required.
Tools Required:
- Screwdriver (Phillips head recommended)
- Wire Strippers/Crimpers (if terminating new coaxial cables)
- Coaxial Cable (RG6 or RG59, as appropriate)
- Existing low-voltage mounting bracket or electrical box (not included)
Step-by-Step Installation:
- Prepare the Location: Ensure you have an existing low-voltage mounting bracket or electrical box installed in the wall where you intend to place the wall plate. If not, install one according to local electrical codes.
- Route Coaxial Cables: Pull the necessary coaxial cables through the mounting bracket or electrical box opening. Ensure there is enough slack to comfortably work with the cables.
- Terminate Cables (if necessary): If your coaxial cables are not already terminated with F-connectors, use appropriate tools to strip the cable and crimp F-connectors onto the ends. Ensure a clean, secure connection.
- Connect Cables to Jack Insert: Take the dual F-connector jack insert. Screw the F-connectors from your coaxial cables onto the back of the jack insert. Hand-tighten them securely.
Image: The Morris 85221 Dual F Connector Wall Plate, showing the two F-type connectors on the front. The coaxial cables connect to the corresponding F-type ports on the rear of the insert.
- Insert Jack into Wall Plate: The dual F-connector jack insert is designed to snap or fit securely into the opening of the decorative wall plate. Gently push the insert into the plate until it is flush and stable.
- Mount the Wall Plate: Carefully push the assembled wall plate and jack insert into the mounting bracket or electrical box, guiding the cables into the wall cavity. Align the screw holes on the wall plate with those on the mounting bracket.
- Secure the Wall Plate: Use the provided mounting screws to secure the wall plate to the mounting bracket. Do not overtighten, as this can crack the plastic plate.
- Final Check: Ensure the wall plate is flush against the wall and all connections are secure. You can now connect your devices (TV, modem, etc.) to the front F-connectors.
For optimal signal quality, avoid sharp bends in coaxial cables and ensure all connections are tight.
Operation
The Morris 85221 Decorative Dual F Connector Wall Plate functions as a passive pass-through for coaxial signals. Once installed, simply connect your F-type coaxial cables from your devices (e.g., television, cable modem, satellite receiver) to the F-connector ports on the front of the wall plate. The plate provides a stable and organized connection point, ensuring signal integrity between your in-wall cabling and external devices.
Maintenance
The Morris 85221 Wall Plate requires minimal maintenance.
- Cleaning: To clean the surface of the wall plate, use a soft, damp cloth. Avoid abrasive cleaners or solvents, as these may damage the plastic finish.
- Connection Check: Periodically check the F-connector connections for tightness to ensure optimal signal quality. Loose connections can lead to signal degradation.
- Inspection: Inspect the wall plate for any signs of damage or wear. If damage is observed, replace the unit to maintain safety and performance.
Troubleshooting
If you experience issues with your coaxial connection, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| No signal or poor signal quality | Loose F-connector connections | Ensure all F-connectors (both at the wall plate and device) are hand-tightened securely. |
| Damaged coaxial cable | Kinked, cut, or frayed cable | Inspect the coaxial cable for damage. Replace if necessary. |
| Incorrect cable type | Using an incompatible coaxial cable (e.g., wrong impedance) | Ensure you are using standard RG6 or RG59 coaxial cables for your application. |
| Wall plate appears loose | Mounting screws are not tight | Gently tighten the mounting screws. Do not overtighten. |
If issues persist after troubleshooting, contact a qualified technician or your service provider.
Warranty and Support
Morris Products stands behind the quality of its products. For specific warranty information, please refer to the documentation included with your purchase or visit the official Morris Products website. For technical support or inquiries, please contact Morris Products customer service.
Morris Products Contact Information: (Typically found on product packaging or manufacturer's website)
- Website: www.morrisproducts.com (Example link, verify actual website)
- Phone: Refer to manufacturer's website for current contact numbers.
