Introduction
This user manual provides detailed instructions for the installation, operation, and maintenance of the Rosewill RSV 4 x 3.5-Inch HDD Cage (Model RASA-11001). This product is designed to expand storage capacity within compatible computer cases, specifically as an add-on module for Rosewill RSV-R4000 and RSV-L4000 chassis. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.
Safety Information
- Always disconnect power from your computer system before installing or removing any components.
- Handle all components with care to prevent damage.
- Ensure proper grounding to avoid electrostatic discharge (ESD) which can damage sensitive electronic components.
- Do not expose the HDD cage to moisture or extreme temperatures.
- This product is intended for use with 3.5-inch HDDs. Ensure compatibility with your hard drives.
- Verify correct power connector orientation to prevent damage to the unit or connected drives. Incorrect connection can lead to component failure or fire.
Package Contents
Please verify that all items are present in the package:
- Rosewill RSV 4 x 3.5-Inch HDD Cage (RASA-11001)
- User Manual
- Mounting Screws (quantity may vary)
Image showing the Rosewill RSV 4 x 3.5-Inch HDD Cage, its user manual, and the product packaging.
Product Overview
The Rosewill RASA-11001 HDD Cage is designed to house up to four 3.5-inch hard disk drives. It features a 120mm cooling fan to maintain optimal operating temperatures for the installed drives.
Front view of the Rosewill HDD Cage, highlighting the integrated 120mm fan for cooling.
Detailed view of the 120mm cooling fan with its protective grille.
Side view illustrating the four individual drive bays designed for 3.5-inch hard drives.
Setup and Installation
- Prepare Your System: Power off your computer and disconnect the power cord from the wall outlet. Open your computer case to access the internal drive bays.
- Identify Compatible Bays: This HDD cage is designed to fit into three standard 5.25-inch drive bays. Ensure your case has three consecutive, unoccupied 5.25-inch bays.
- Install the HDD Cage: Carefully slide the Rosewill HDD cage into the selected 5.25-inch bays from the front of your computer case. Align the screw holes on the cage with those on your case.
- Secure the Cage: Use the provided mounting screws to secure the HDD cage to your computer case. Typically, two to four screws on each side are sufficient.
- Install Hard Drives:
- Gently slide each 3.5-inch HDD into an available drive tray within the cage. Ensure the SATA data and power connectors on the HDD align with the backplane connectors of the cage.
- Push firmly until the drive is fully seated and secured.
- Connect Power and Data Cables:
- Connect the appropriate SATA data cables from the HDD cage's backplane to your motherboard's SATA ports.
- Connect the power cables (typically Molex or SATA power connectors) from your power supply to the corresponding power inputs on the HDD cage. Ensure correct polarity and secure connections.
- Connect the 120mm fan's power connector to an available fan header on your motherboard or power supply.
- Cable Management: Organize cables neatly to ensure proper airflow within the case.
- Close Case and Power On: Close your computer case, reconnect the power cord, and power on your system. Your operating system should detect the newly installed hard drives.
Operation
Once installed, the Rosewill HDD Cage operates passively, providing a secure housing and cooling for your hard drives. The integrated 120mm fan will activate with system power to ensure consistent airflow over the drives.
- Drive Access: Access to the installed hard drives is managed through your computer's operating system, similar to any other internal storage device.
- Hot-Swap Capability: While the cage supports hot-swap functionality for SATA drives, always ensure your motherboard and operating system are configured for hot-swapping and that drives are safely ejected or unmounted before removal to prevent data loss.
- LED Indicators: The cage may feature LED indicators for power and drive activity. Refer to your system's documentation or the cage's specific design for LED behavior.
Maintenance
- Dust Removal: Periodically inspect the 120mm fan and the cage for dust accumulation. Use compressed air or a soft brush to gently remove dust from the fan blades and grilles to maintain optimal airflow.
- Cable Inspection: Occasionally check all connected power and data cables to ensure they are securely seated and not damaged.
- Environmental Conditions: Ensure the computer case is kept in a well-ventilated area, away from direct sunlight, heat sources, and excessive humidity.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Hard drives not detected. |
|
|
| Fan not spinning. |
|
|
| Drives are running hot. |
|
|
Specifications
| Model Number | RASA-11001 |
| HDD Tray Capacity | 4 x 3.5-inch HDDs |
| Cooling Fan | 1 x 120mm |
| Dimensions (L x W x H) | 8.27" x 5.12" x 5.9" (21 x 13 x 15 cm) |
| Item Weight | 1 pound (approximately 16 ounces) |
| Compatibility | Designed as an add-on module for Rosewill RSV-R4000 and RSV-L4000 chassis. Requires three 5.25-inch drive bays. |
Warranty Information
Rosewill products typically come with a limited warranty. For specific warranty terms and conditions applicable to your RASA-11001 HDD Cage, please refer to the warranty card included with your product or visit the official Rosewill website. Keep your purchase receipt as proof of purchase for warranty claims.
Customer Support
For technical assistance, troubleshooting, or warranty inquiries, please contact Rosewill customer support:
- Website: Visit the official Rosewill website for support resources, FAQs, and contact information.
- Online Store: Rosewill Amazon Store
