Introduction
This instruction manual provides essential information for the proper use and maintenance of your Briggs & Stratton 794696 Key Set. This key set is a genuine Briggs & Stratton replacement part designed to ensure optimal performance and compatibility with specific Briggs & Stratton snow engines, primarily the 10D000 and 122000 series.
Using genuine Briggs & Stratton parts helps maintain the integrity and performance of your equipment and ensures compliance with applicable emission regulations.
Product Overview
Image 1: The Briggs & Stratton 794696 Key Set. This image displays the red plastic key, which serves as a safety and ignition component for compatible engines.
The Briggs & Stratton 794696 Key Set is a critical component for starting and stopping your snow engine. It functions as a safety switch, allowing the engine to operate only when inserted correctly. This part replaces the older Briggs & Stratton part number 695756.
Setup and Installation
The Briggs & Stratton 794696 Key Set is designed for straightforward installation. Follow these steps to properly insert the key into your equipment:
- Locate the Key Slot: Identify the key slot on your Briggs & Stratton powered snow engine. This is typically found near the ignition or control panel.
- Orient the Key: Ensure the key is oriented correctly. The specific design of the key (as shown in Image 1) will guide its proper insertion.
- Insert the Key: Gently push the key into the key slot until it is fully seated. Do not force the key if it does not slide in easily. Forcing it may cause damage to the key or the ignition system.
- Verify Engagement: Once inserted, the key should sit securely in the slot. A properly inserted key completes the electrical circuit, allowing the engine to be started.
Important: Always ensure the engine is turned off and cooled down before inserting or removing the key, especially during maintenance or storage.
Operating Instructions
The key set serves two primary functions: enabling engine operation and acting as a safety shut-off.
- To Start the Engine: With the key fully inserted into the key slot, proceed with the standard starting procedure for your equipment (e.g., prime, choke, pull start or electric start). The key must be in place for the engine to receive ignition.
- To Stop the Engine: To safely stop the engine, simply pull the key out of the key slot. This action interrupts the ignition circuit, causing the engine to shut down.
- Safety Precaution: Always remove the key when the equipment is unattended, being stored, or undergoing maintenance to prevent accidental starting.
Maintenance
Proper care of your key set will ensure its longevity and reliable function.
- Cleaning: Keep the key free from dirt, debris, and moisture. Wipe it with a clean, dry cloth as needed.
- Storage: Store the key in a safe, dry place when not in use, preferably away from extreme temperatures. Consider attaching it to a keyring or a designated spot to prevent loss.
- Inspection: Periodically inspect the key for any signs of wear, cracks, or damage. If the key appears damaged, replace it with a new genuine Briggs & Stratton 794696 Key Set.
Troubleshooting
If you encounter issues related to the key set, consider the following:
- Engine Does Not Start with Key Inserted:
- Ensure the key is fully and correctly seated in the slot.
- Check for any visible damage to the key or the key slot.
- Verify that other starting procedures (fuel, choke, primer, battery for electric start) are correctly followed.
- If the key is damaged, replace it.
- Key is Difficult to Insert or Remove:
- Inspect the key and the key slot for any obstructions or debris.
- Ensure the key is oriented correctly before insertion.
- Do not force the key. If resistance persists, the key or the key slot may be damaged and require replacement or professional inspection.
- Engine Stops Unexpectedly:
- Check if the key has vibrated loose or partially dislodged from the slot. Re-insert it firmly.
- If the issue persists, it may indicate a problem with the engine's electrical system beyond the key itself. Consult your equipment's main instruction manual or a qualified service technician.
Specifications
| Feature | Detail |
|---|---|
| Part Number | 794696 |
| Replaces Part Number | 695756 |
| Brand | Briggs & Stratton |
| Material | Plastic |
| Color | Multi (typically red) |
| Operation Mode | Manual |
| Compatibility | Most 10D000, 122000 series Briggs & Stratton Snow Engines |
| Dimensions (approx.) | 4 x 3.8 x 0.2 inches |
| Weight (approx.) | 0.32 ounces (9.07 g) |
Warranty Information
As a genuine Briggs & Stratton replacement part, this key set is manufactured to exact OEM standards. Genuine parts are typically covered by the standard Briggs & Stratton warranty for replacement parts. For specific warranty terms and conditions, please refer to the official Briggs & Stratton website or contact their customer service. Using non-genuine parts may void your equipment's warranty.
Support and Contact
For further assistance, technical support, or to locate authorized service centers, please visit the official Briggs & Stratton website or contact their customer support directly.
- Briggs & Stratton Official Website: www.briggsandstratton.com
- Briggs & Stratton Store on Amazon: Visit Store
