Introduction
Thank you for choosing the Hudson Valley Lighting 5508-HN Altamont 1 Light Pendant. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.
The Altamont pendant features a conical metal shade with unique ring-and-rod chains, finished in Historic Nickel. Its design offers versatile ambient illumination suitable for various indoor settings.
Safety Information
WARNING: Risk of electric shock. Always turn off the main power supply at the circuit breaker or fuse box before installing, servicing, or cleaning this fixture.
- All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
- This product must be installed by a person familiar with the construction and operation of the product and the hazards involved.
- Do not connect this fixture to an ungrounded electrical system.
- Never use a bulb exceeding the maximum wattage specified for this fixture.
- Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Package Contents
Carefully unpack your fixture and check that all parts are included. If any parts are missing or damaged, do not attempt to assemble or install the fixture. Contact customer service for assistance.
- Pendant Fixture (Shade, Socket Assembly)
- Canopy Assembly (Mounting Plate, Canopy, Collar Ring)
- Mounting Hardware (Mounting Screws, Wire Nuts)
- Instruction Manual
Installation Instructions
Tools Required (Not Included):
- Phillips Head Screwdriver
- Flathead Screwdriver
- Wire Strippers
- Electrical Tape
- Safety Glasses
Pre-Installation:
- Ensure the power is turned off at the circuit breaker before starting.
- Clear the work area and gather all necessary tools and components.
- Review the wiring diagram and instructions carefully.
Mounting the Fixture:
- Carefully remove the old fixture (if applicable) and disconnect all wiring.
- Attach the mounting plate to the junction box using the provided mounting screws. Ensure it is securely fastened.
- Adjust the length of the pendant chain/rod as desired.
- Connect the fixture's ground wire (bare copper or green) to the house ground wire (bare copper or green) using a wire nut.
- Connect the fixture's neutral wire (white) to the house neutral wire (white) using a wire nut.
- Connect the fixture's hot wire (black or smooth) to the house hot wire (black or smooth) using a wire nut.
- Carefully tuck all wires into the junction box.
- Position the canopy over the mounting plate and secure it with the collar ring or screws.
- Install the appropriate light bulb (see Operating Instructions for bulb type).
Image: The Altamont pendant light fixture, showcasing its conical shade and Historic Nickel finish, suspended by its rod and chain assembly.
Operating Instructions
Once the fixture is securely installed and the bulb is in place, restore power at the circuit breaker. The pendant light can then be operated using your wall switch (if connected) or the integrated pull chain switch, if present.
Bulb Information:
- Bulb Type: Incandescent
- Bulb Base: E26 (Medium Base)
- Maximum Wattage: 75 Watts
- Ensure the bulb is fully screwed into the socket. Do not overtighten.
Maintenance
Cleaning:
- Always turn off power and allow the fixture to cool before cleaning.
- Wipe the fixture with a soft, dry cloth.
- Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
Bulb Replacement:
- Turn off power at the circuit breaker.
- Allow the bulb to cool completely before touching it.
- Carefully unscrew the old bulb and replace it with a new E26 incandescent bulb, not exceeding 75 watts.
- Restore power.
Troubleshooting
If your fixture is not functioning correctly, refer to the table below for common issues and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check circuit breaker or fuse. Ensure wall switch is on. |
| Bulb is loose or burned out. | Tighten or replace bulb. | |
| Incorrect wiring. | Turn off power and recheck wiring connections. Consult an electrician if needed. | |
| Light flickers. | Loose bulb or wiring connection. | Turn off power, tighten bulb, and check wiring connections. |
If these steps do not resolve the issue, contact a qualified electrician or Hudson Valley Lighting customer service.
Specifications
| Brand: | Hudson Valley Lighting |
| Model: | 5508-HN Altamont |
| Finish: | Historic Nickel |
| Material: | Metal (Fixture), Glass (Shade) |
| Product Dimensions: | 8"L x 8"W x 9"H |
| Light Source Type: | Incandescent |
| Number of Light Sources: | 1 |
| Bulb Base: | E26 |
| Max Wattage: | 75 Watts |
| Voltage: | 120 Volts |
| Mounting Type: | Ceiling Mount |
| Assembly Required: | Yes |
| Item Weight: | 3 Pounds |
Warranty and Support
Warranty:
This Hudson Valley Lighting fixture is covered by a 1-year manufacturer's limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or normal wear and tear.
Customer Support:
For technical assistance, missing parts, or warranty claims, please contact Hudson Valley Lighting customer service. Have your model number (5508-HN) and proof of purchase available when contacting support.
You can find contact information on the official Hudson Valley Lighting website or through your retailer.
