Thomson ROC 4411 4-in-1 Universal Remote Control Instruction Manual

1. Introduction

The Thomson ROC 4411 is a versatile 4-in-1 universal remote control designed to consolidate the control of up to four different audio/video devices into a single unit. It is compatible with over 1000 brands, offering convenience and ease of use for your home entertainment system. This manual provides comprehensive instructions for its setup, operation, and maintenance.

2. Package Contents

• 1x Thomson ROC 4411 Universal Remote Control
• 1x Code List
• 2x AAA Batteries
• 1x Instruction Manual

3. Product Features

• Controls up to 4 devices: TV, DVD, SAT/STB (Satellite/Set-Top Box), and AMP (Amplifier).
• Compatible with over 1000 brands of devices.
• Includes a learning function to copy commands from original remote controls.
• Features a macro function for executing a sequence of commands with a single button press.
• Backlit device selection keys, Program (+/-), and Volume (+/-) keys for enhanced visibility.
• Ergonomic design with an anti-slip bottom for comfortable handling.
• Color-coded keys for specific CA-TV and IP-TV functions.
• Fingerprint-resistant surface material.

4. Remote Control Layout

The Thomson ROC 4411 remote control features a logical button layout for intuitive operation. Key sections include device selection buttons at the top, followed by learning, setup, and macro functions, navigation controls, and a numeric keypad.

This image displays the full layout of the Thomson ROC 4411 universal remote control, highlighting its ergonomic design and clearly labeled buttons for various functions such as TV, DVD, SAT/STB, AMP, volume, channel, menu, and numeric keypad. The device selection buttons are located at the top, while the learning, setup, and macro buttons are positioned below them.

5. Setup

5.1. Battery Installation

1. Open the battery compartment cover on the back of the remote control.
2. Insert the two AAA batteries, ensuring correct polarity (+ and -).
3. Close the battery compartment cover securely.

5.2. Device Code Programming

To control your devices, you must program the remote with the appropriate codes. Refer to the included code list for your specific device brand.

1. Turn on the device you wish to control (e.g., TV).
2. Press and hold the SETUP button until the red LED lights up continuously.
3. Press the device button you want to program (e.g., TV). The LED will flash once and then remain lit.
4. Enter the 4-digit code for your device brand from the code list. After entering each digit, the LED will flash briefly. If the code is valid, the LED will turn off. If the code is invalid, the LED will flash rapidly.
5. Point the remote at your device and test the functions (e.g., Power, Volume). If the device responds, the programming is successful.
6. If the device does not respond, repeat the process with the next code listed for your brand.

5.3. Automatic Code Search

If you cannot find a suitable code in the list, you can use the automatic code search function.

1. Turn on the device you wish to control.
2. Press and hold the SETUP button until the red LED lights up continuously.
3. Press the device button you want to program (e.g., TV). The LED will flash once and then remain lit.
4. Press the POWER button once. The LED will flash, indicating the remote is searching for a code.
5. Point the remote at your device. When the device turns off, immediately press the OK button to save the code.
6. Test the remote's functions. If not all functions work, repeat the search process.

6. Operating Instructions

6.1. Device Selection

To control a specific device, press the corresponding device button (TV, DVD, SAT/STB, or AMP) at the top of the remote. The selected device button will light up briefly, indicating it is ready to send commands to that device.

6.2. Basic Functions

• POWER: Turns the selected device on or off.
• VOL +/-: Adjusts the volume of the selected device.
• CH +/-: Changes channels on the selected device.
• MENU: Accesses the menu of the selected device.
• EXIT: Exits the menu or current function.
• GUIDE: Displays the electronic program guide (if supported by the device).
• Numeric Keypad (0-9): For direct channel input or menu navigation.

6.3. Special Functions

This diagram visually explains three key features of the remote: the backlight function, indicated by a light bulb icon; the macro function, labeled 'MACRO'; and the learning function, shown with two remote controls transmitting signals to each other.

6.3.1. Learning Function

The learning function allows you to copy specific commands from your original remote control to the Thomson ROC 4411, even if a code is not available or if you prefer a different button layout.

1. Place the Thomson remote and your original remote control head-to-head on a flat surface, approximately 2-5 cm apart.
2. Press and hold the LEARN button on the Thomson remote until the red LED lights up continuously.
3. Press the device button (e.g., TV) on the Thomson remote for which you want to learn a command. The LED will flash once and then remain lit.
4. Press the button on the Thomson remote where you want to store the new command. The LED will flash slowly.
5. Press and hold the corresponding button on your original remote control. The LED on the Thomson remote will flash rapidly three times and then turn off, indicating successful learning.
6. Repeat steps 4 and 5 for any other commands you wish to learn.
7. To exit learning mode, press the LEARN button again.

6.3.2. Macro Function

A macro allows you to program a sequence of up to 15 commands to be executed with a single button press.

1. Press and hold the MACRO button until the red LED lights up continuously.
2. Press the button on the Thomson remote where you want to store the macro (e.g., a numeric button or a specific function button). The LED will flash once and then remain lit.
3. Enter the sequence of commands you want to store in the macro, pressing each button in the desired order. The LED will flash briefly after each button press.
4. After entering all commands (up to 15), press the MACRO button again to save the macro and exit programming mode. The LED will turn off.
5. To execute the macro, simply press the button where you stored it.

6.3.3. Backlight Function

The device selection buttons, Program (+/-), and Volume (+/-) keys are backlit for easy visibility in low-light conditions. The backlight activates automatically when a button is pressed and remains on for a few seconds.

7. Maintenance

• Cleaning: Use a soft, dry cloth to clean the remote control. Do not use abrasive cleaners or solvents.
• Battery Replacement: Replace batteries when the remote's performance diminishes or the LED indicator flashes to signal low power. Always replace both batteries simultaneously with new AAA batteries.
• Storage: If the remote will not be used for an extended period, remove the batteries to prevent leakage.

8. Troubleshooting

• Remote not working: Check if the batteries are inserted correctly and are not depleted. Replace batteries if necessary. Ensure the correct device button is selected.
• Device not responding: Verify that the remote is pointed directly at the device and there are no obstructions. Re-program the device code, trying alternative codes from the list.
• Learning function not working: Ensure the original remote's batteries are fresh. Place the remotes closer together. Ensure the original remote is functioning correctly.
• Limited range: Replace batteries. Ensure there are no obstructions between the remote and the device.

9. Specifications

10. Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Thomson customer service directly. Keep your proof of purchase for any warranty claims.