1. Introduction
This manual provides comprehensive instructions for the Feit Electric BPESL23T2/2/RP Compact Fluorescent Lamp (CFL). This 23-watt twist-shaped bulb is designed to provide light output equivalent to a 100-watt incandescent bulb, offering significant energy efficiency and a long operational lifespan. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
Image 1.1: Packaging for the Feit Electric BPESL23T2/2/RP CFL Bulb 2-pack, showing product details and energy savings information.
2. Important Safety Information
Always follow basic safety precautions when installing or replacing light bulbs to reduce the risk of fire, electric shock, or personal injury.
- Turn off power: Always disconnect power to the fixture before installing, removing, or inspecting the bulb.
- Indoor use only: This bulb is designed for indoor use in dry locations. Do not use in wet or damp environments unless the fixture is specifically rated for such conditions.
- Not for enclosed fixtures: Avoid using this CFL bulb in fully enclosed luminaires, as this can shorten its lifespan.
- Non-dimmable: This bulb is not compatible with dimmer switches. Using it with a dimmer may cause damage to the bulb or the dimmer, and will void the warranty.
- Contains Mercury: As a Compact Fluorescent Lamp, this product contains a small amount of mercury. Handle with care. For information on clean-up and safe disposal, visit epa.gov/cfl.
- Proper disposal: Dispose of used bulbs according to local regulations. Do not dispose of in regular household waste.
- Avoid touching hot bulb: Allow the bulb to cool completely before handling.
3. Setup and Installation
Follow these steps to properly install your Feit Electric CFL bulb:
- Ensure Power is Off: Before beginning, locate the light switch or circuit breaker controlling the fixture and turn off the power.
- Remove Old Bulb (if applicable): If replacing an existing bulb, carefully unscrew it counter-clockwise from the socket. Allow it to cool if it was recently on.
- Install New Bulb: Gently screw the Feit Electric BPESL23T2/2/RP CFL bulb clockwise into the standard E26 medium screw base socket until it is snug. Do not overtighten.
- Restore Power: Turn the power back on at the light switch or circuit breaker.
Image 3.1: A single Feit Electric BPESL23T2/2/RP CFL bulb, showing its spiral twist shape and E26 medium screw base.
4. Operating Instructions
Operating your Feit Electric CFL bulb is straightforward:
- Turning On/Off: Use the standard wall switch connected to your light fixture to turn the bulb on or off.
- Warm-up Time: CFL bulbs require a short warm-up period to reach full brightness. This bulb may take a noticeable amount of time (up to a minute) to achieve its full light output and color temperature after being switched on.
- Non-Dimmable: As stated in the safety information, this bulb is not designed for use with dimmer switches. Attempting to dim this bulb will likely result in flickering, reduced lifespan, or damage.
5. Maintenance
The Feit Electric CFL bulb requires minimal maintenance to ensure its long life and performance.
- Cleaning: Ensure the power is off and the bulb is cool before cleaning. Wipe the bulb with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the bulb.
- Replacement: When the bulb reaches the end of its operational life, replace it following the installation steps outlined in Section 3. Remember to dispose of the old bulb responsibly due to its mercury content.
6. Troubleshooting Guide
If you encounter issues with your Feit Electric CFL bulb, refer to the following table for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Bulb does not light up. | No power to the fixture; Bulb not screwed in properly; Bulb has reached end of life. | Check power switch and circuit breaker. Ensure bulb is securely screwed into socket. Replace bulb if necessary. |
| Bulb flickers or dims. | Used with a dimmer switch; Loose connection; Cold ambient temperature. | Do not use with dimmer switches. Ensure bulb is tightly screwed in. CFLs may flicker briefly in very cold conditions until warmed up. |
| Bulb takes a long time to reach full brightness. | Normal operation for CFLs. | This is expected behavior. Allow up to a minute for the bulb to reach full light output. |
| Bulb makes a buzzing sound. | Incompatible fixture; Loose connection; Used with a dimmer. | Ensure the fixture is compatible with CFLs. Tighten the bulb. Do not use with dimmer switches. |
7. Product Specifications
Detailed technical specifications for the Feit Electric BPESL23T2/2/RP CFL bulb:
| Specification | Value |
|---|---|
| Brand | Feit Electric |
| Model Number | BPESL23T2/2/RP |
| Light Type | CFL (Compact Fluorescent Lamp) |
| Wattage | 23 Watts |
| Incandescent Equivalent Wattage | 100 Watts |
| Brightness | 1600 Lumens |
| Color Temperature | 2700 Kelvin (Soft White) |
| Bulb Shape Size | T2 (Twist) |
| Bulb Base | E26 (Medium Screw Base) |
| Voltage | 120 Volts |
| Light Source Operating Life | 12,000 Hours (approx. 11 years based on 3 hrs/day) |
| Specific Uses For Product | Indoor use only |
| Item Weight | 0.55 Pounds |
| UPC | 017801874402 |
Image 7.1: Lighting Facts label, detailing brightness, energy cost, life, light appearance, and energy used for the bulb.
8. Warranty and Customer Support
Feit Electric products are manufactured to high-quality standards. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official Feit Electric website. Keep your purchase receipt for warranty claims.