Moen 131553BN Pop Up Waste Kit, Brushed Nickel Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Moen 131553BN Pop Up Waste Kit in Brushed Nickel. Please read these instructions carefully before beginning installation to ensure proper function and longevity of the product.

Safety Information

• Always turn off the water supply to the sink before beginning any plumbing work.
• Wear appropriate personal protective equipment, such as safety glasses and gloves.
• If you are unsure about any step, consult a qualified plumber.
• Keep small parts away from children.

Package Contents

Verify that all components are present before starting installation:

• Pop Up Drain Assembly (tailpiece, body, stopper)
• Mounting Nut
• Washers/Gaskets (rubber, friction)
• Overflow Hole (if applicable to your model)

Image: Moen 131553BN Pop Up Waste Kit. This image displays the main components of the pop-up waste kit, including the drain body, stopper, and associated hardware.

Tools Required

• Adjustable Wrench or Basin Wrench
• Plumber's Putty or Silicone Sealant
• Rag or Towel
• Bucket (for catching water)

Setup and Installation

Follow these steps for proper installation of the pop-up waste kit:

1. Prepare the Sink Opening: Ensure the sink drain opening is clean and free of old sealant or debris.
2. Apply Sealant: Apply a thin bead of plumber's putty or silicone sealant around the underside of the drain flange (the top part of the drain that sits in the sink).
3. Insert Drain Body: Insert the drain body through the sink opening from the top. Ensure the overflow hole on the drain body (if present) aligns with the overflow opening in the sink. Note: Some sinks, like vessel sinks, may not have an overflow. This kit is designed to accommodate sinks with an overflow hole.
4. Secure from Below: From underneath the sink, slide the rubber washer, then the friction washer, and finally thread the mounting nut onto the drain body. Hand-tighten first, then use an adjustable wrench to tighten securely. Do not overtighten.
5. Connect to P-Trap: Connect the tailpiece of the pop-up drain to your existing P-trap assembly. Ensure all connections are hand-tightened, then snugged with a wrench.
6. Test for Leaks: Turn on the water supply and fill the sink. Check all connections for leaks. If leaks occur, tighten connections slightly or reapply sealant as needed.

Operating Instructions

The Moen 131553BN Pop Up Waste Kit features a simple push-to-seal and push-to-open mechanism.

• To Close the Drain: Gently push down on the top of the drain stopper until it clicks into the closed position. This will seal the drain, allowing the sink to hold water.
• To Open the Drain: Gently push down on the top of the drain stopper again. It will click and pop up, allowing water to drain freely from the sink.

Maintenance

Regular maintenance ensures optimal performance and extends the life of your pop-up waste kit.

• Cleaning: Clean the visible parts of the drain regularly with a soft cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the brushed nickel finish.
• Stopper Removal: For deeper cleaning or to clear minor clogs, the pop-up stopper can typically be removed by pulling it straight up firmly. Clean any hair or debris from the stopper and inside the drain body. Reinsert by pushing it back down until it seats properly.
• Check for Leaks: Periodically inspect the connections under the sink for any signs of leaks. Address any leaks promptly to prevent water damage.

Troubleshooting

Here are solutions to common issues you might encounter:

• Drain Leaks:
  • Ensure all nuts are tightened securely, but do not overtighten.
  • Verify that plumber's putty or silicone sealant was properly applied under the drain flange. Reapply if necessary.
  • Check that all washers and gaskets are correctly seated and not damaged.
• Slow Draining:
  • Remove the pop-up stopper and clear any hair or debris that may have accumulated around it or inside the drain body.
  • If the issue persists, the clog may be further down in the P-trap or drainpipe, requiring further plumbing attention.
• Stopper Not Sealing/Opening Properly:
  • Ensure the stopper is free of debris and can move freely.
  • Check if the stopper mechanism is fully engaged when pushed.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the official Moen website or contact Moen customer service directly. Keep your purchase receipt as proof of purchase.

Official Moen Website: www.moen.com