Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Toro DDCWP-4-9V Waterproof 4 Station Battery Controlled Controller. Please read this manual thoroughly before using the product to ensure proper function and longevity.
Image 1: Front view of the Toro DDCWP-4-9V Waterproof 4 Station Battery Controlled Controller, showing the digital display, control buttons, and dial.
Setup
1. Unpacking and Inspection
Carefully remove the controller from its packaging. Inspect for any signs of damage. Ensure all components are present as listed in the packing contents.
2. Battery Installation
The DDCWP-4-9V controller requires two 9V batteries (not included) for operation. Locate the battery compartment, typically on the back or side of the unit. Insert the batteries, observing the correct polarity (+/-). Secure the battery compartment cover.
3. Mounting the Controller
Choose a suitable location for mounting the controller. It is designed to be waterproof and can be installed outdoors. Use appropriate screws or mounting hardware to secure the controller to a wall or post. Ensure it is easily accessible for programming and maintenance.
Image 2: Side view of the Toro DDCWP-4-9V controller, illustrating its compact design.
4. Wiring to Solenoids
Connect the controller's wires to your irrigation system's DC latching solenoids. This controller requires 9-12 VDC DC latching solenoids; it is not compatible with 24 VAC solenoids. Each station wire from the controller corresponds to a specific solenoid. Ensure all connections are secure and waterproof.
Operating Instructions
1. Initial Power-Up and Reset
Upon battery installation, the display should activate. If the display remains blank or the unit is unresponsive, locate the reset button (often a small pinhole) and press it using a paperclip or similar pointed object. This will reset the controller.
2. Setting Current Time and Date
- Turn the dial to the "SET TIME/DAY" position.
- Use the arrow buttons to adjust the year, month, day, and time.
- Press "NEXT" or turn the dial to confirm each setting.
3. Programming Automatic Irrigation
The controller allows for multiple programs (e.g., A, B, C) to manage different watering schedules for various zones.
- Set Start Times: Turn the dial to "START TIMES". Use the "PROG A,B,C" button to select a program. Use arrow buttons to set desired start times for each program.
- Set Run Times: Turn the dial to "RUN TIMES". Select a program and then use arrow buttons to set the duration for each station (1-4).
- Set Water Days: Turn the dial to "WATER DAYS". Select a program and choose specific days of the week for watering, or select interval watering (e.g., every 2 days).
4. Manual Operation
To manually operate a station or program:
- Turn the dial to "MANUAL PROGRAMS" or "MANUAL STATION".
- Select the desired program or station using the arrow buttons.
- Press the "ON" button to start watering.
- Press the "OFF" button to stop watering manually.
5. Seasonal Adjust
The "SEASON ADJUST" feature allows you to globally increase or decrease watering durations for all programs by a percentage, adapting to seasonal changes without reprogramming each station.
6. Turning Off the Controller
To temporarily disable all watering, turn the dial to the "OFF" position.
Maintenance
- Battery Replacement: Replace batteries annually or when the low battery indicator appears on the display. Use fresh 9V alkaline batteries.
- Cleaning: Wipe the controller's exterior with a damp cloth. Do not use abrasive cleaners or solvents.
- Winterization: In freezing climates, remove the controller and batteries for storage indoors during winter months to prevent damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display is blank or unresponsive. | Dead batteries, unit locked up. | Replace batteries. Press the reset button with a paperclip. |
| Stations not watering. | Controller in "OFF" mode, incorrect programming, faulty solenoids, wiring issues. | Ensure dial is in "AUTO RUN". Verify program settings (start times, run times, water days). Check solenoid connections and functionality. Ensure correct DC latching solenoids are used. |
| Watering at incorrect times. | Incorrect time/date setting, incorrect program start times. | Adjust current time and date. Review and correct program start times. |
Specifications
- Model: DDCWP-4-9V
- Stations: 4
- Power Source: 2 x 9V Batteries (not included)
- Solenoid Compatibility: 9-12 VDC DC Latching Solenoids
- Dimensions (W x D x H): 5.75 x 2.75 x 5 inches (14.6 cm x 7.0 cm x 12.7 cm)
- Weight: 1.5 pounds (0.68 kg)
- Waterproof Rating: Fully waterproof and submersible
Warranty Information
Toro products are designed for durability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Toro website. Keep your purchase receipt as proof of purchase for any warranty claims.
Customer Support
For further assistance, technical support, or to purchase replacement parts, please contact Toro customer service. Contact information can be found on the official Toro website or in the documentation provided with your controller.
Online Resources: www.toro.com
