Introduction
This manual provides essential information for the installation and maintenance of your genuine Frigidaire 316075103 Oven Bake Element. This component is designed to restore optimal baking function to compatible electric ranges and stoves. Please read all instructions carefully before proceeding with installation.
Important Safety Information
- Disconnect Power: Always ensure the appliance's power supply is completely disconnected at the circuit breaker before attempting any installation or repair. Failure to do so can result in serious injury or electrical shock.
- Wear Protective Gear: Wear appropriate personal protective equipment, including safety glasses and gloves, during installation to prevent injury.
- Professional Assistance: If you are unsure about any step of the installation process, consult a qualified appliance technician.
- Genuine Parts: Use only genuine Frigidaire replacement parts to ensure proper fit, function, and safety.
Compatibility
The Frigidaire 316075103 Oven Bake Element is compatible with a wide range of Frigidaire, Electrolux, Tappan, White-Westinghouse, Kelvinator, and Gibson electric oven models. It is crucial to verify compatibility with your specific appliance model before purchasing and installing this part.
Image Description: A graphic titled "Is Your Part Compatible?" displaying a partial list of Frigidaire oven models compatible with the 316075103 bake element. The text advises checking the Frigidaire website for a complete overview.
Refer to your appliance's user manual or the manufacturer's website for a comprehensive list of compatible models. The model number of your appliance is typically located on a label inside the oven door frame or on the back of the appliance.
Installation Instructions
This installation is recommended for experienced DIYers. The estimated installation time is approximately 15 minutes.
Tools Required:
- 1/4" nut driver
- Flat-head screwdriver
- Gloves
- Safety glasses
Step-by-Step Guide:
- Prepare the Oven: Ensure the oven is cool. Disconnect the oven from its power source by unplugging it or turning off the circuit breaker.
- Access the Element: Open the oven door. Locate the existing bake element at the bottom of the oven cavity.
- Remove Old Element:
- Using a 1/4" nut driver, remove the screws securing the bake element to the back wall of the oven.
- Carefully pull the element forward a few inches to expose the electrical terminals.
- Disconnect the wires from the terminals of the old element. It may be helpful to take a picture before disconnecting to ensure correct re-connection.
- Gently pull the old element completely out of the oven cavity.
- Install New Element:
- Carefully insert the new Frigidaire 316075103 bake element into the oven cavity, guiding the terminals through the holes in the back wall.
- Connect the electrical wires to the terminals of the new element. Ensure a secure connection.
- Push the element fully into place, aligning the mounting brackets with the screw holes.
- Secure the new element with the screws removed in step 3.
- Test the Oven: Close the oven door. Reconnect the oven to its power source. Turn on the oven to a bake setting to ensure the new element heats up properly.
Image Description: The Frigidaire 316075103 Oven Bake Element, a black, U-shaped heating element with two electrical terminals at its ends, ready for installation.
Image Description: The Frigidaire 316075103 Oven Bake Element displayed alongside a modern electric range, illustrating its intended use as a replacement part.
Maintenance
To prolong the life of your oven bake element and ensure efficient operation:
- Keep Clean: Regularly clean the oven interior, avoiding excessive spills directly onto the element.
- Avoid Impact: Be careful not to strike the element with cookware or cleaning tools, as this can cause damage.
- Inspect Periodically: Periodically inspect the element for any signs of damage, such as cracks, blisters, or uneven heating.
Troubleshooting
If your oven is not heating properly after replacing the bake element, consider the following:
- No Heat:
- Verify the oven is plugged in and the circuit breaker is on.
- Check that the electrical wires are securely connected to the element terminals.
- Ensure the element is properly seated and secured in its mounting brackets.
- Uneven Heating:
- Confirm the element is fully functional and glowing evenly when heated.
- Ensure no debris or food particles are obstructing the element's heat distribution.
- Element Not Glowing:
- If the element does not glow red when the oven is set to bake, it may indicate a faulty connection or a problem with the oven's control board.
If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician.
Product Specifications
| Model Number | 316075103 |
| Brand | Frigidaire |
| Product Dimensions | 19.25 x 18.75 x 1.5 inches |
| Item Weight | 12.8 ounces |
| Power Source | Corded Electric |
| Fuel Type | Electric |
| Heater Surface Material | Ceramic |
| Color | Black |
Warranty and Support
As a genuine Frigidaire part, this bake element is engineered to exact specifications for optimal performance. For warranty information or technical support, please refer to your original appliance documentation or contact Frigidaire customer service directly. Using genuine parts ensures compatibility and maintains the integrity of your appliance's warranty.
