Pentair LXD10 Feed Hose Float Replacement User Manual

Introduction

This manual provides essential information for the installation, function, and maintenance of the Pentair LXD10 White Feed Hose Float Replacement. This component is specifically designed for use with Pentair Legend II and Kreepy Krauly Legend II automatic pool cleaners.

The feed hose float plays a crucial role in the proper operation of your automatic pool cleaner by ensuring the feed hose maintains optimal buoyancy and position within the pool, allowing the cleaner to move freely and effectively.

Product Overview

Figure 1: Pentair LXD10 White Feed Hose Float Replacement. This image shows the Pentair LXD10 White Feed Hose Float Replacement, a U-shaped white plastic component designed to maintain the buoyancy of the cleaner's feed hose.

The Pentair LXD10 is a direct replacement part for the feed hose float used in specific Pentair automatic pool cleaner models. It is white in color and designed for durability in pool environments.

Key Features:

• Feed hose float replacement for specific Pentair models.
• Compatible with Pentair Legend II and Kreepy Krauly Legend II automatic pool cleaner models LX2000, LX5000G, and LX5000GG.
• Available in white color to match existing components.

Setup and Installation

The LXD10 feed hose float is designed for straightforward replacement of an existing, worn, or damaged float. Follow these steps for proper installation:

1. Disconnect Cleaner: Before beginning, ensure your automatic pool cleaner is disconnected from the pool's filtration system and removed from the water.
2. Identify Existing Float: Locate the feed hose floats along the cleaner's hose. These are typically U-shaped components that clip onto the hose.
3. Remove Old Float: Carefully unclip or slide off the old feed hose float from the hose. If the float is damaged, it may break apart during removal.
4. Install New Float: Position the new Pentair LXD10 feed hose float over the hose at the desired location. Gently but firmly press the float onto the hose until it securely clips into place. Ensure the hose is fully seated within the float's groove.
5. Verify Placement: Confirm that the new float is securely attached and does not slide freely along the hose. The fit should be snug to ensure proper buoyancy.
6. Reconnect Cleaner: Once all necessary floats are replaced, reconnect your automatic pool cleaner to the filtration system and return it to the pool.

Note: The fit of the float onto the hose may be tight to ensure secure attachment and proper function. Apply steady, even pressure during installation.

Operation

The Pentair LXD10 feed hose float operates passively as part of your automatic pool cleaner's hose assembly. Its primary function is to provide buoyancy to the feed hose, preventing it from sinking to the bottom of the pool. This buoyancy is critical for:

• Hose Management: Keeping the hose elevated helps prevent tangling and kinking, allowing the cleaner to move freely across the pool surface.
• Optimal Cleaner Movement: Proper hose buoyancy ensures the cleaner can navigate the pool efficiently without being hindered by a dragging or improperly positioned hose.
• Reduced Wear: By keeping the hose off the pool floor, the float helps reduce friction and wear on the hose itself.

No active user intervention is required for the operation of the float once installed. Its effectiveness is maintained through its structural integrity and material properties.

Maintenance

While the LXD10 feed hose float is a durable component, regular inspection and basic maintenance can extend its lifespan and ensure optimal performance of your pool cleaner.

• Regular Inspection: Periodically inspect all feed hose floats for signs of wear, cracking, discoloration, or damage. Check if they are still securely attached to the hose.
• Cleaning: If the floats accumulate algae, dirt, or mineral deposits, gently clean them with a soft brush and mild pool-safe cleaner. Rinse thoroughly with fresh water.
• Replacement: If a float shows significant signs of wear, becomes loose, or loses its buoyancy, it should be replaced promptly to maintain the efficiency of your pool cleaner. Refer to the "Setup and Installation" section for replacement instructions.

Troubleshooting

Most issues related to the feed hose float are straightforward and involve replacement. Consider the following if you suspect a float-related problem:

• Hose Sinking or Dragging:
  • Cause: Damaged, missing, or improperly installed floats.
  • Solution: Inspect all floats along the hose. Replace any that are cracked, broken, or no longer providing adequate buoyancy. Ensure all floats are securely clipped onto the hose.
• Cleaner Movement Issues (Hose Related):
  • Cause: Hose tangling or kinking due to insufficient buoyancy.
  • Solution: Verify that the correct number of floats are installed and that they are spaced appropriately along the hose as per your cleaner's original setup. Replace any faulty floats.
• Float Not Staying Attached:
  • Cause: Float clip is worn, or the hose diameter is incorrect for the float.
  • Solution: Ensure you are using the correct LXD10 float for your Pentair Legend II or Kreepy Krauly Legend II cleaner hose. If the float is new and still not staying attached, it may be defective and should be replaced.

Specifications

Warranty and Support

For specific warranty information regarding the Pentair LXD10 Feed Hose Float Replacement, please refer to the documentation provided with your original Pentair pool cleaner or contact Pentair customer support directly. Warranty terms typically cover manufacturing defects.

For technical support, replacement parts, or further assistance, please visit the official Pentair website or contact their customer service department. Contact information can usually be found on the Pentair website or in the original product manual for your pool cleaner.

Disclaimer: This manual is for informational purposes only. Always refer to the official manufacturer's instructions and safety guidelines when installing or maintaining pool equipment.