Permatex 82588 Electrical Contact and Parts Cleaner User Manual

1. Product Overview

The Permatex 82588 Electrical Contact and Parts Cleaner is a specialized solution designed for cleaning electrical and electronic devices. This fast-evaporating, non-corrosive cleaner leaves no residue, ensuring optimal performance of your components. It effectively removes grease, dirt, oil, flux, and other surface contaminants.

Key Features:

• Formulated for cleaning electrical and electronic devices.
• Fast evaporating, non-corrosive, and leaves no residue.
• Does not contain ozone-depleting HCFCs.
• Safe for use on all metals and most plastics.
• Effectively removes grease, dirt, oil, flux, and other surface contaminants.

Suggested Applications:

• Electronic parts: circuit boards, computer components, relay switches.
• Electric parts: electric motors, generators, starters, pumps, motor windings, solenoids, and compressors.

This product is an alternative to CFC-113, 1,1,1-trichloroethane, and perchlorethylene solvents.

2. Safety Information

WARNING: Read entire label before using this product. Failure to follow warnings and directions may result in serious injury or property damage.

• Extremely Flammable: Contents under pressure. Keep away from heat, sparks, open flames, and hot surfaces. No smoking.
• Vapor and Spray Harmful: Use only in a well-ventilated area. Avoid breathing vapors or spray mist.
• Eye and Skin Irritant: Avoid contact with eyes and skin. In case of contact, flush thoroughly with water. Seek medical attention if irritation persists.
• Do Not Apply While Equipment is Energized: Ensure all power is turned off and disconnected before application.
• Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
• Keep Out of Reach of Children.

3. Setup

Before using the Permatex 82588 cleaner, ensure the extension tube (straw) is securely attached to the actuator for precise application.

Attaching the Extension Tube:

1. Locate the small red extension tube provided with the can.
2. Carefully insert one end of the tube into the small hole on the spray nozzle actuator. Ensure a snug fit to prevent the tube from dislodging during use.
3. If the tube is too tight to insert, gently trim a very small amount from the end of the tube or use a fine file to slightly widen the opening for a better fit.

4. Operating Instructions

Follow these steps for effective cleaning of electrical and electronic components:

1. Ensure Power is Off: Always turn off and disconnect power to the equipment or device before applying the cleaner. This is crucial for safety and to prevent damage.
2. Shake Can: Shake the can well before each use.
3. Apply Cleaner: Hold the can upright and spray directly onto the electrical contacts or parts to be cleaned. Use the extension tube for hard-to-reach areas or for more precise application.
4. Allow to Dry: The cleaner is fast-evaporating and will dry quickly, leaving no residue. Ensure the area is thoroughly dry before re-energizing the equipment.
5. Ventilation: Use in a well-ventilated area to allow vapors to dissipate.

For heavily contaminated areas, a second application may be necessary. Always allow adequate drying time between applications.

5. Maintenance

Regular cleaning of electrical and electronic contacts can help prevent future issues and extend the lifespan of your devices.

• Periodic Cleaning: For devices exposed to dust, dirt, or moisture, consider periodic cleaning with Permatex 82588 to maintain optimal conductivity and prevent contact failure.
• Storage: Store the can in a cool, dry place away from direct sunlight and sources of ignition. Keep the cap on when not in use.

6. Troubleshooting

If you encounter issues after using the cleaner, consider the following:

• Residue Appears: Although designed to be residue-free, excessive application or insufficient drying time in poorly ventilated areas might lead to minor residue. Re-apply sparingly and ensure proper ventilation and drying.
• Continued Malfunction: If cleaning does not resolve the issue, the problem may not be related to dirty contacts. Consult a qualified technician for further diagnosis.
• Material Compatibility: While safe on most plastics, always test on an inconspicuous area first if you are unsure about material compatibility.

7. Product Specifications

8. Warranty & Support

For warranty information or product support, please refer to the official Permatex website or contact their customer service directly. Keep your purchase receipt for any warranty claims.

Visit the official Permatex Store for more products and information.