Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Beverage-Air DW79-B-24 Remote Horizontal Bottle Cooler. Please read this manual thoroughly before operating the unit and retain it for future reference. This cooler is designed for commercial use, featuring a deep well design and self-contained refrigeration system for optimal beverage cooling.
Front view of the Beverage-Air DW79-B-24 bottle cooler, showcasing its black painted steel exterior, stainless steel top with three sliding lids, and integrated bottle opener on the right side.
Setup and Installation
The Beverage-Air DW79-B-24 is a freestanding unit. Proper placement and initial setup are crucial for performance and longevity.
Unpacking
- Carefully remove all packaging materials, including any protective films or tapes.
- Inspect the unit for any shipping damage. Report any damage to your carrier immediately.
Placement
- Place the cooler on a level, sturdy surface capable of supporting its weight (approximately 379 lbs when empty, plus contents).
- Ensure adequate ventilation around the unit. Do not block the air intake or exhaust vents.
- Avoid direct sunlight or proximity to heat-generating appliances.
- Dimensions: 80"W x 26-1/2"D x 33-3/4"H. Allow sufficient space for door operation and maintenance access.
Electrical Connection
- Connect the unit to a dedicated electrical circuit as specified on the product's data plate.
- Ensure the power supply matches the unit's requirements (e.g., voltage, amperage).
Initial Start-up
- After placement and electrical connection, allow the unit to sit for at least 2 hours before plugging it in. This allows refrigerants to settle.
- Plug in the unit and allow it to reach the desired operating temperature before loading products.
Operating Instructions
Your Beverage-Air bottle cooler is designed for efficient and convenient beverage storage and dispensing.
Electronic Controls
- The unit features electronic controls for precise temperature management. Refer to the control panel for temperature display and adjustment buttons.
- Set the desired temperature according to your beverage cooling requirements.
Loading Products
- Utilize the three sliding lids to access the deep well interior.
- Arrange beverages using the five adjustable epoxy coated wire dividers to optimize space and organization.
- The cooler has a case capacity of 32 cases (12 oz. bottles) or 45-3/4 cases (12 oz. cans). Do not overload the unit beyond its stated capacity.
- Ensure proper air circulation around products for efficient cooling.
Bottle Cap Opener and Catcher
- An integrated bottle cap opener and cap catcher are provided for user convenience.
- Regularly empty the cap catcher to prevent overflow.
Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your Beverage-Air cooler.
Cleaning the Exterior
- Clean the black painted steel exterior with a mild soap and water solution. Avoid abrasive cleaners.
- Wipe the stainless steel top with a damp cloth and dry thoroughly to prevent water spots.
Cleaning the Interior
- Periodically clean the galvanized interior and epoxy coated wire dividers with a mild, food-safe cleaning solution.
- Ensure the unit is unplugged before cleaning the interior.
Condenser Coil Cleaning
- The condenser coil should be cleaned regularly (e.g., monthly or quarterly, depending on environment) to maintain efficiency.
- Consult a qualified service technician for condenser coil cleaning, especially for units using R290 Hydrocarbon refrigerant.
Gasket Maintenance
- Inspect door gaskets regularly for tears or damage. Clean them with warm, soapy water.
- Ensure gaskets form a tight seal to prevent cold air loss.
Troubleshooting
This section provides solutions to common issues. For problems not listed or if issues persist, contact qualified service personnel.
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit not cooling | Power supply issue, thermostat setting, dirty condenser coil, blocked airflow. | Check power connection, adjust thermostat, clean condenser coil, ensure proper ventilation. |
| Excessive noise | Loose components, fan obstruction, compressor issue. | Check for loose parts, clear obstructions, contact service if compressor related. |
| Water on floor | Clogged drain line, excessive humidity, damaged drain pan. | Clear drain line, ensure proper sealing, inspect drain pan. |
Important: Any repairs involving the refrigeration system or electrical components should only be performed by a certified technician.
Specifications
| Feature | Detail |
|---|---|
| Brand | Beverage-Air |
| Model Number | DW79HC-B |
| Exterior Finish | Black painted steel |
| Interior Finish | Galvanized |
| Top Material | Stainless steel |
| Lid Type | Solid, Sliding (3 lids) |
| Dividers | 5 adjustable epoxy coated wire dividers |
| Case Capacity (12 oz. bottles) | 32 cases |
| Case Capacity (12 oz. cans) | 45-3/4 cases |
| Refrigerant Type | R290 Hydrocarbon |
| Compressor Horsepower | 1/4 HP |
| Cubic Feet | 24.1 cu. ft |
| Dimensions (W x D x H) | 80" x 26-1/2" x 33-3/4" |
| Item Weight | 379 lbs |
| Certifications | cULus, UL EPH Classified, UL-Sanitation, Energy Star Compliant |
| Manufacturing Location | Made in USA |
Warranty and Support
For specific warranty information, please refer to the documentation provided with your purchase or contact Beverage-Air directly. General support inquiries can be directed to the manufacturer or your authorized dealer.
Manufacturer: TigerChef (as per product specifications)
For service or technical assistance, please have your model number (DW79HC-B) and serial number ready.
