Invacare 9805P Hydraulic Patient Lift User Manual

Introduction

This manual provides comprehensive instructions for the safe and effective use of the Invacare 9805P Hydraulic Patient Lift. Designed for patient transfer, this lift offers a reliable solution for caregivers in various homecare settings. Please read this manual thoroughly before operating the device to ensure patient safety and proper functionality.

Figure 1: Invacare 9805P Hydraulic Patient Lift. This image shows the assembled patient lift with its hydraulic pump, mast, boom, and base.

Safety Information

Important: Always prioritize patient safety. Failure to follow these instructions may result in serious injury or damage to the equipment.

• Ensure the patient's weight does not exceed the lift's maximum capacity of 450 pounds.
• Always use the appropriate sling size and type for the patient and transfer task.
• Inspect the lift and sling for any signs of wear, damage, or loose components before each use. Do not use if damaged.
• Ensure all casters are locked (if applicable) when the lift is stationary and during patient transfer to prevent unintended movement.
• Maintain a clear path of travel and be aware of surroundings to avoid collisions.
• Never leave a patient unattended in the lift.
• Operate the hydraulic pump smoothly and avoid sudden movements.
• Seek assistance if you are unsure about any aspect of operation or if the patient's condition requires more than one caregiver.

Setup and Assembly

The Invacare 9805P Hydraulic Patient Lift requires some assembly upon receipt. Follow these steps carefully.

1. Unpacking: Carefully remove all components from the packaging. Verify all parts are present according to the packing list.
2. Base Assembly: Attach the mast assembly to the base. Ensure all bolts are securely tightened.
3. Boom and Swivel Bar: Connect the boom to the mast and the padded swivel bar to the boom. Double-check all connections for stability.
4. Casters: Ensure casters are properly installed. Note that optional locking casters may ship separately and should be installed as per their specific instructions.
5. Initial Inspection: Before first use, perform a thorough visual inspection of the assembled lift. Check for any loose parts, damage, or obstructions.

For transport, the lift is designed for easy disassembly. To disassemble, reverse the assembly steps, paying attention to secure all components for transport.

Operating Instructions

Follow these steps for safe and effective patient transfer using the Invacare 9805P Hydraulic Patient Lift.

1. Prepare the Patient: Position the patient appropriately for sling application. Ensure the sling is correctly placed under the patient, following the sling manufacturer's instructions.
2. Position the Lift: Roll the lift to the patient. Ensure the base legs are spread wide enough for stability and to clear any obstacles. Lock the casters to prevent movement.
3. Attach the Sling: Securely attach the sling straps to the padded swivel bar hooks. Double-check that all straps are correctly attached and not twisted.
4. Raise the Patient: Operate the hydraulic pump handle to slowly raise the patient. Observe the patient carefully during the lift. The lift has a range of 20 to 64 inches, allowing for lifting from the floor if necessary.
5. Transfer: Once the patient is clear of the surface, unlock the casters and carefully maneuver the lift to the destination. The 360-degree patient rotation feature allows for precise positioning without side-to-side sway.
6. Lower the Patient: Once positioned over the target surface (e.g., bed, chair), lock the casters. Slowly open the hydraulic release valve to lower the patient onto the surface.
7. Remove the Sling: Once the patient is safely and securely on the new surface, detach the sling straps from the swivel bar and remove the sling.

Always maintain control of the lift using the push handle during operation and transfer.

Maintenance

Regular maintenance ensures the longevity and safe operation of your Invacare 9805P Hydraulic Patient Lift.

• Cleaning: Clean all surfaces with a mild detergent and water. Do not use abrasive cleaners or solvents. Ensure the lift is dry before storage or next use.
• Inspection: Periodically inspect all moving parts, bolts, and welds for wear or damage. Pay close attention to the hydraulic cylinder for leaks and the casters for smooth operation.
• Lubrication: Lubricate moving joints and caster axles as needed with a silicone-based lubricant to ensure smooth operation.
• Sling Care: Follow the sling manufacturer's washing and care instructions. Replace slings that show signs of wear, fraying, or damage.

Troubleshooting

This section addresses common issues you might encounter with your patient lift.

• Lift does not raise:
  • Ensure the hydraulic release valve is fully closed.
  • Check for sufficient hydraulic fluid. Consult a qualified technician if fluid levels are low or if there are signs of a leak.
• Lift lowers too quickly or unexpectedly:
  • Ensure the hydraulic release valve is not fully open. It should be opened slowly and controlled.
  • Inspect the hydraulic system for leaks. Contact a qualified technician for repair.
• Casters do not roll smoothly:
  • Check for debris or hair wrapped around the caster wheels.
  • Lubricate caster axles if necessary.
  • Ensure casters are not damaged. Replace if broken.
• Lift feels unstable:
  • Verify all assembly bolts are securely tightened.
  • Ensure the base legs are spread to their widest position during transfers.
  • Do not exceed the maximum weight capacity.

For issues not covered here or if problems persist, contact Invacare customer support or a qualified service technician.

Specifications

Warranty and Support

For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Invacare website.

For technical assistance, parts, or service, please contact Invacare Customer Support:

• Website: www.invacare.com
• Customer Service: Refer to the contact information provided on the Invacare website or product packaging.