1. Introduction
This manual provides essential instructions for the proper installation, operation, and maintenance of your Atwood 56096 Piezo Ignitor. Please read this manual thoroughly before attempting any procedures to ensure safe and correct usage. Retain this manual for future reference.
2. Product Overview
The Atwood 56096 Piezo Ignitor is a replacement component designed to provide reliable ignition for compatible Atwood stove models. It is constructed from quality materials to ensure durability and consistent performance.
Figure 1: Front view of the Atwood 56096 Piezo Ignitor. This image displays the main body of the ignitor, including the spark output terminal and mounting points.
Figure 2: Side view of the Atwood 56096 Piezo Ignitor. This perspective highlights the overall shape and additional connection points of the unit.
2.1 What's in the Box
- One (1) Atwood 56096 Ignitor for 33 & 34 Series Stoves
3. Safety Information
Always prioritize safety when working with gas appliances and electrical components. Failure to follow these safety guidelines may result in property damage, personal injury, or death.
- Disconnect Power: Before attempting any installation or maintenance, ensure that all power to the appliance is disconnected at the main breaker or fuse box.
- Disconnect Gas Supply: Turn off the gas supply to the appliance before beginning any work.
- Qualified Personnel: If you are unsure about any step of the installation or repair process, it is recommended to consult a qualified service technician.
- Proper Fit: Verify that this part is the correct replacement for your specific stove model before installation. An incorrect part may lead to malfunction or unsafe conditions.
- Ventilation: Ensure adequate ventilation when working with gas appliances.
4. Compatibility
The Atwood 56096 Piezo Ignitor is specifically designed for use with Atwood 33 Series and 34 Series Stoves. It is crucial to confirm that your stove model falls within these series to ensure proper fit and function. Refer to your stove's original documentation or model number for verification.
5. Installation (Setup)
This section provides general guidance for replacing the piezo ignitor. For detailed, model-specific instructions, always refer to the service manual for your particular Atwood 33 or 34 Series Stove.
- Prepare for Installation: Ensure the stove is completely cool. Disconnect all electrical power and turn off the gas supply to the stove.
- Access the Ignitor: Depending on your stove model, you may need to remove burner grates, burner caps, or the stove top to gain access to the existing ignitor.
- Disconnect Old Ignitor: Carefully disconnect the spark wires from the old ignitor. Note the position of each wire for correct re-connection. There may also be mounting screws or clips securing the ignitor.
- Remove Old Ignitor: Once disconnected and unsecured, remove the old ignitor unit.
- Install New Ignitor: Position the new Atwood 56096 Piezo Ignitor in the same location as the old unit. Secure it with any original mounting screws or clips.
- Reconnect Wires: Reconnect the spark wires to the new ignitor, ensuring they are firmly attached to their correct terminals.
- Reassemble Stove: Reassemble any parts of the stove that were removed to access the ignitor.
- Restore Power and Gas: Carefully restore the gas supply and electrical power to the stove. Check for any gas leaks before attempting to operate the stove.
6. Operation
The piezo ignitor generates a high-voltage spark to ignite the gas from the burner. Follow these steps to operate your stove after ignitor installation:
- Ensure Gas Supply: Confirm that the gas supply to the stove is turned on.
- Prepare Burner: Place any cooking utensils on the burner grate as needed.
- Turn Knob to LITE: Push in and turn the desired burner control knob to the "LITE" or "IGNITE" position. You should hear the gas flowing.
- Activate Ignitor: While holding the burner knob in the "LITE" position, press and hold the piezo ignitor button (if separate) or continue holding the knob in the "LITE" position if it integrates the ignitor function. You should hear a clicking sound and see a spark at the burner.
- Verify Ignition: Once the burner ignites, release the ignitor button (if applicable) and continue to hold the burner knob in for a few seconds to allow the thermocouple to heat up. Then, release the knob and adjust to the desired flame setting.
- Troubleshooting Ignition: If the burner does not ignite within a few seconds, release the knob, allow gas to dissipate, and repeat the process. If ignition issues persist, refer to the Troubleshooting section.
7. Maintenance
The Atwood 56096 Piezo Ignitor is designed for minimal maintenance. However, periodic inspection can help ensure its longevity and reliable performance.
- Visual Inspection: Periodically inspect the ignitor and its connections for any signs of wear, corrosion, or damage. Ensure all spark wires are securely attached.
- Cleaning: If the ignitor tip or surrounding area becomes dirty with food debris or grease, carefully clean it using a soft brush or cloth. Ensure the stove is cool and gas/power are off before cleaning. Avoid using abrasive cleaners.
- Replacement: If the ignitor consistently fails to produce a strong spark or shows visible damage, it may need to be replaced.
8. Troubleshooting
If you experience issues with your Atwood 56096 Piezo Ignitor, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No spark when ignitor is activated. | Loose or disconnected spark wires. Faulty ignitor. No power to stove (if applicable). | Check all spark wire connections. Ensure power is supplied to the stove. If connections are secure and power is present, the ignitor may need replacement. |
| Weak or inconsistent spark. | Dirty ignitor tip. Loose connections. Ignitor nearing end of life. | Clean the ignitor tip. Verify all connections are tight. Consider replacing the ignitor if issues persist after cleaning and checking connections. |
| Burner does not ignite, but spark is present. | No gas supply. Clogged burner port. | Ensure gas supply is on. Check for obstructions in the burner ports. This issue is typically not related to the ignitor itself. |
If troubleshooting steps do not resolve the issue, contact a qualified service technician.
9. Specifications
- Brand: Atwood
- Model: 56096 (also referred to as WW56096)
- Manufacturer Part Number: 56096
- Item Weight: 1.44 ounces
- Product Dimensions: 2.31 x 0.06 x 0.02 inches
- ASIN: B004QMXIAC
- First Available Date: March 4, 2011
- Compatibility: Atwood 33 Series and 34 Series Stoves
10. Warranty and Support
Specific warranty information for the Atwood 56096 Piezo Ignitor is not provided within this manual. For details regarding warranty coverage, technical support, or to purchase replacement parts, please contact Atwood customer service directly or visit their official website.
Always refer to the manufacturer's official channels for the most accurate and up-to-date support information.