WOODCRAFT 146137W
WOODCRAFT Woodshop Clock with Thermometer and Hygrometer
Model: 146137W
Introduction
Thank you for choosing the WOODCRAFT Woodshop Clock with integrated Thermometer and Hygrometer. This versatile instrument is designed to provide accurate timekeeping along with essential environmental readings for your workspace. Its robust design and clear display make it an ideal addition to any woodshop or similar environment.
Key features include:
- 10-inch diameter clock face with chrome hands for easy readability.
- Integrated thermometer displaying temperature in 5-degree Fahrenheit increments.
- Integrated hygrometer displaying relative humidity in 2% intervals.
- Durable construction suitable for various environments.
Figure 1: Front view of the Woodshop Clock, displaying the time, temperature, and humidity.
Setup
1. Battery Installation
The Woodshop Clock requires one (1) AA battery (not included) for its quartz movement. To install the battery:
- Locate the battery compartment on the back of the clock.
- Open the battery compartment cover.
- Insert one AA battery, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Close the battery compartment cover securely.
2. Setting the Time
After installing the battery, set the time:
- Locate the time-setting knob on the back of the clock mechanism.
- Gently rotate the knob clockwise or counter-clockwise until the clock hands display the correct time.
3. Placement
For optimal performance and accurate readings from the thermometer and hygrometer, consider the following placement guidelines:
- Place the clock in a location that is representative of the general temperature and humidity of your woodshop or desired area.
- Avoid direct sunlight, heat sources (e.g., heaters, vents), or areas with extreme drafts, as these can affect the accuracy of the temperature and humidity readings.
- Ensure the clock is mounted securely on a wall or placed on a stable surface.
Figure 2: Dimensions of the Woodshop Clock, showing its 10-inch diameter.
Operation
Reading the Clock
The main dial displays the current time with clear hour, minute, and second hands. The large 10-inch black face with chrome hands and markings ensures easy readability from a distance.
Reading the Thermometer
The thermometer dial is located on the lower left side of the clock face. It displays the ambient temperature in Fahrenheit, with markings in 5-degree increments. The red needle indicates the current temperature.
Reading the Hygrometer
The hygrometer dial is located on the lower right side of the clock face. It displays the relative humidity as a percentage, with markings in 2% intervals. The red needle indicates the current relative humidity.
Figure 3: Detail view of the thermometer and hygrometer for precise readings.
Maintenance
Battery Replacement
When the clock hands begin to slow down or stop, it is an indication that the AA battery needs to be replaced. Follow the battery installation steps outlined in the "Setup" section.
Cleaning
To clean the clock, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or spray directly onto the clock face or mechanism, as this may damage the finish or internal components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clock not keeping accurate time or stopped. | Low or dead battery. | Replace the AA battery with a fresh one. Ensure correct polarity. |
| Clock not keeping accurate time or stopped. | Mechanism issue. | Ensure the time-setting knob is not stuck or damaged. If the issue persists after battery replacement, contact customer support. |
| Inaccurate thermometer or hygrometer readings. | Improper placement (e.g., direct sunlight, near heat source, strong drafts). | Relocate the clock to a more stable environment, away from direct heat, cold, or drafts. Allow time for the readings to stabilize in the new location. |
| Inaccurate thermometer or hygrometer readings. | Sensor obstruction or damage. | Ensure nothing is blocking the sensor areas on the back or sides of the clock. If damage is visible, contact customer support. |
Specifications
- Product Dimensions: 9.9 x 9.9 x 2.1 inches
- Item Weight: 1.37 Pounds
- Model Number: 146137W
- Power Source: 1 x AA Battery (not included)
- Temperature Display: Fahrenheit, 5-degree increments
- Humidity Display: Relative Humidity (%), 2% intervals
- Manufacturer: Woodcraft Supply
Warranty
WOODCRAFT products are manufactured to high-quality standards. For specific warranty information regarding your Woodshop Clock, please refer to the packaging or contact WOODCRAFT customer support directly. Keep your purchase receipt as proof of purchase.
Customer Support
If you have any questions, require assistance, or encounter issues not covered in this manual, please contact WOODCRAFT customer support:
- Website: www.woodcraft.com (Please note: This is a general example, actual support contact details may vary. Refer to product packaging for official contact information.)
- Phone: Refer to the WOODCRAFT website or product packaging for current contact numbers.
When contacting support, please have your product model number (146137W) and purchase details ready.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.