Introduction
This manual provides instructions for the Carrera 20061659 GO/Digital 143 See Saw Slot Car Racing Accessory. This accessory is designed to enhance your Carrera GO!!!, GO!!! Plus, and DIGITAL 143 race tracks by introducing an interactive seesaw element, adding a new dimension of challenge and excitement to your races.
Safety Information
WARNING: Not suitable for children under 36 months due to small parts which may present a choking hazard.
Package Contents
- 1 x Carrera GO - See Saw (one seesaw unit designed for a single track lane)
Setup Instructions
The Carrera See Saw accessory is designed for easy integration into your existing Carrera GO!!!, GO!!! Plus, or DIGITAL 143 race track system.
Step 1: Track Preparation
Ensure your race track is assembled on a flat, stable surface. Disconnect power to the track before adding or removing any track sections to prevent electrical hazards.
Step 2: Integrating the See Saw
Identify a suitable straight section of your track where you wish to install the seesaw. The seesaw unit replaces a standard straight track section. Carefully disconnect the existing straight track section by gently pulling the connectors apart.
Image: The Carrera See Saw track accessory, illustrating its design and connection points.
Connect the Carrera See Saw accessory to the adjacent track sections. Ensure the connectors are firmly seated to maintain electrical continuity and a smooth, level track surface. The seesaw is designed to be powered directly by the track itself, requiring no additional power source.
Image: Slot cars positioned on the Carrera See Saw, demonstrating its tilting action.
Step 3: Power Connection
Once the seesaw is securely integrated into the track, reconnect the power to your race track. The seesaw will be ready for use.
Operating Instructions
The seesaw adds an interactive challenge to your race. As a slot car approaches the seesaw, its weight will cause the track section to tilt, creating a dynamic obstacle.
- Approach Speed: Experiment with different speeds to successfully navigate the seesaw. Driving too slowly may result in the car losing momentum and getting stuck. Driving too fast may cause the car to de-slot upon impact or landing.
- Dynamic Play: The seesaw provides a dynamic element, requiring drivers to adjust their technique and timing. It can be used to create exciting moments and challenge opponents.
- Multiple Cars: The accessory includes one seesaw unit per track lane, allowing multiple cars to interact with their respective seesaws simultaneously during a race.
Maintenance
To ensure optimal performance and longevity of your Carrera See Saw accessory, follow these maintenance guidelines:
- Cleaning: Regularly clean the track rails and the seesaw surface with a soft, dry, lint-free cloth to remove dust, dirt, and debris. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the plastic or electrical contacts.
- Storage: When not in use, store the seesaw in a clean, dry place away from direct sunlight, extreme temperatures, and excessive humidity. Proper storage helps prevent warping or material degradation.
- Inspection: Periodically inspect the seesaw for any signs of wear, cracks, or damage to the plastic components or electrical contacts. Ensure all track connections are secure and free from corrosion.
Troubleshooting
If you encounter issues with your Carrera See Saw accessory, consider the following troubleshooting steps:
- Car De-slotting Frequently: If cars frequently de-slot on or around the seesaw, try adjusting your approach speed. Ensure the track connections leading to and from the seesaw are perfectly aligned and flat, without any gaps or bumps. Check that the car's guide keel and braids are in good condition.
- No Movement or Power to Seesaw: The seesaw is powered by the track. Check all track connections to ensure they are secure and that there is continuous electrical contact throughout the entire track layout. Verify that the main power supply to your track is functioning correctly.
- Seesaw Sticking or Not Tilting Smoothly: Ensure no debris (e.g., dust, small plastic pieces) is lodged in the seesaw's pivot mechanism. Gently clean the pivot points if necessary. Avoid applying lubricants unless specifically recommended by Carrera, as some lubricants can attract dust.
Specifications
- Model Number: 20061659
- Compatibility: Carrera GO!!!, Carrera GO!!! Plus, Carrera DIGITAL 143 race tracks
- Material: Approximately 99% plastic, 1% metal components
- Product Dimensions: 15.55 x 3.35 x 4.72 inches (39.5 x 8.5 x 12 cm)
- Item Weight: 7.1 ounces (201 grams)
- Recommended Age: 6 years and up
Warranty and Support
For specific warranty information or technical support regarding your Carrera product, please refer to the official Carrera website or contact their customer service department directly. It is recommended to keep your purchase receipt as proof of purchase for any warranty claims.
Manufacturer: Carrera
Official Website: www.carrera-toys.com
