PIXEL RC-201/CB1 Shutter Release Cord User Manual

1. Introduction

Thank you for choosing the PIXEL RC-201/CB1 Shutter Release Cord. This manual provides detailed instructions for the proper setup, operation, and maintenance of your new accessory. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.

What's in the Box:

• 1 x PIXEL RC-201/CB1 Shutter Release Cord

Figure 1: Packaging of the PIXEL RC-201/CB1 Shutter Release Cord.

2. Safety Information

Please observe the following safety precautions to prevent damage to the product or injury to yourself:

• Do not expose the cord to water or extreme humidity.
• Avoid dropping or subjecting the cord to strong impacts.
• Keep out of reach of children.
• Do not attempt to disassemble or modify the product.
• Ensure the cord is securely connected to the camera to prevent accidental disconnection.

3. Product Overview

The PIXEL RC-201/CB1 is a wired shutter release cord designed to provide remote control over your Olympus DSLR camera's shutter functions. It helps to reduce camera shake, especially during long exposures or when using telephoto lenses. The cord measures 110cm in length, offering flexibility in positioning.

Figure 2: The PIXEL RC-201/CB1 Shutter Release Cord.

Figure 3: Close-up view of the PIXEL RC-201/CB1 Shutter Release Cord showing the cable and remote.

4. Setup

To set up your PIXEL RC-201/CB1 Shutter Release Cord:

1. Locate the remote control port on your compatible Olympus DSLR camera. This port is typically covered by a small rubber flap.
2. Carefully insert the CB1 cable connector of the shutter release cord into the camera's remote control port. Ensure a firm connection.
3. The cord is now ready for use. No additional power source or software installation is required.

Compatibility:

This shutter release cord is compatible with the following Olympus camera models:

• Olympus E-1
• Olympus E-3
• Olympus E-10
• Olympus E-20
• Olympus E-5

Note: The CB1 cable is permanently attached to the transmitter and cannot be exchanged for other cable types.

5. Operating Instructions

The PIXEL RC-201/CB1 Shutter Release Cord offers intuitive control over your camera's shutter:

1. Focusing: Gently press the button on the remote halfway down. This will activate your camera's autofocus system, similar to pressing the camera's shutter button halfway.
2. Taking a Picture: Once focused, press the button fully down to trigger the camera's shutter and capture an image.
3. Continuous Shooting: If your camera is set to continuous shooting mode, pressing and holding the button fully down will allow the camera to take multiple photos in sequence until the button is released or the camera's buffer is full.
4. Bulb Mode (Long Exposure): For bulb mode photography, set your camera to bulb mode. Press the button fully down and hold it for the desired exposure time. Release the button to end the exposure. Some cameras may require a specific setting to lock the shutter open in bulb mode; refer to your camera's manual for details.

Using the shutter release cord helps to minimize camera shake, resulting in sharper images, especially in low light or with long focal lengths.

6. Maintenance

To ensure the longevity and proper functioning of your shutter release cord:

• Cleaning: Use a soft, dry cloth to wipe the cord and remote control. Do not use liquid cleaners or solvents.
• Storage: Store the cord in a cool, dry place away from direct sunlight and extreme temperatures. Avoid tightly coiling the cable to prevent damage.
• Inspection: Periodically check the cable and connectors for any signs of wear or damage. If damage is observed, discontinue use.

7. Troubleshooting

If you encounter issues with your PIXEL RC-201/CB1 Shutter Release Cord, consider the following:

• Cord not triggering shutter:
  • Ensure the cable is fully and securely inserted into the camera's remote control port.
  • Verify that your camera model is listed as compatible (Olympus E-1, E-3, E-10, E-20, E-5).
  • Check your camera's settings to ensure it is not in a mode that disables external shutter release (e.g., certain self-timer modes or locked states).
• Autofocus not engaging (half-press):
  • Confirm the cable is properly connected.
  • Ensure your camera's autofocus system is enabled and functioning correctly with the camera's own shutter button.
• Intermittent connection:
  • Inspect the cable and connectors for any visible damage or bent pins.
  • Try gently wiggling the connector while it's plugged in to see if the connection stabilizes. If not, the cable may be damaged.

If problems persist, please contact customer support.

8. Specifications

9. Warranty and Support

For warranty information and customer support, please refer to the documentation provided with your purchase or visit the official PIXEL website. Keep your proof of purchase for any warranty claims.

If you require further assistance or have questions not covered in this manual, please contact PIXEL customer service through their official channels.