KitchenAid Architect Series II KSRS25RVMK Refrigerator User Manual

Important Safety Instructions

Your safety and the safety of others are very important. This manual provides important safety messages. Always read and obey all safety messages.

• Read all instructions before using the refrigerator.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Do not allow children to climb, stand, or hang on the shelves of the refrigerator. They could damage the refrigerator and seriously injure themselves.
• Unplug the refrigerator before cleaning or performing any maintenance.
• Ensure proper grounding for electrical safety.
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

Setup and Installation

Unpacking and Location

Remove all packaging materials, tape, and protective film from the refrigerator. Clean any adhesive residue with a soft cloth and warm water. Choose a location with a level floor, away from direct sunlight and heat sources. Allow at least 1/2 inch (1.27 cm) of space between the refrigerator and adjacent walls or cabinets for proper air circulation.

Image: Front view of the KitchenAid Architect Series II KSRS25RVMK Side-by-Side Refrigerator. This image shows the overall design, including the dual doors and the external ice and water dispenser.

Leveling the Refrigerator

It is crucial to level the refrigerator for proper door alignment and operation. Use a level to check the top of the refrigerator. Adjust the front leveling legs by turning them clockwise to raise or counter-clockwise to lower the refrigerator. Ensure both doors close and seal properly.

Water Supply Connection

A cold water supply is required for the ice maker and water dispenser. Connect the refrigerator to a potable water supply using a copper or braided stainless steel water line. Ensure the water pressure is between 30 and 120 psi (207 and 827 kPa). Flush the water system for 3-5 minutes before initial use to remove air and impurities.

Note: Refer to local plumbing codes for installation requirements. A water filter is pre-installed or needs to be installed before use.

Operating Instructions

Temperature Controls

The refrigerator and freezer compartments have separate temperature controls, typically located inside the fresh food compartment or on the external dispenser panel. The recommended temperature settings are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer. Allow 24 hours for the refrigerator to reach stable temperatures after initial setup or temperature adjustments.

Ice and Water Dispenser

The external dispenser provides filtered water and cubed or crushed ice. To dispense water, press a glass against the water paddle. To dispense ice, select the desired ice type (cubed or crushed) and press a glass against the ice paddle. The first few batches of ice may contain air or impurities; discard them.

Lock Feature: The dispenser often includes a lock feature to prevent accidental dispensing, especially useful with children. Refer to your control panel for specific lock button location and operation.

Adjustable Shelves and Crisper Drawers

The refrigerator features cantilever spill-proof glass shelves that can be adjusted to various heights to accommodate different-sized items. To adjust, lift the front of the shelf and pull it out. Reinsert at the desired level. The humidity-controlled crisper drawers are designed to keep fruits and vegetables fresh. Adjust the humidity slider to high for leafy vegetables and low for fruits.

Maintenance and Care

Cleaning the Refrigerator

Clean the interior and exterior of your refrigerator regularly. Unplug the appliance before cleaning. Use a mild detergent and warm water solution for interior surfaces. For stainless steel exteriors, use a stainless steel cleaner and polish, wiping in the direction of the grain. Do not use abrasive cleaners or harsh chemicals.

Replacing the Water Filter

The water filter should be replaced approximately every 6 months or when the "Replace Filter" indicator light illuminates, or water flow to the dispenser decreases significantly. The filter is typically located in the upper right corner of the fresh food compartment or in the base grille. Twist the old filter counter-clockwise to remove, then insert the new filter and twist clockwise until it locks into place. Flush the dispenser with 3-5 gallons of water after replacement to remove air and carbon fines.

Image: A placeholder for an image showing the location and process of replacing the water filter. If an image like "KSRS25RVMK_water_filter_replacement.jpg" were available, it would be placed here.

Condenser Coil Cleaning

For optimal efficiency, clean the condenser coils located behind the base grille at least once a year. Unplug the refrigerator. Remove the base grille and use a vacuum cleaner with a brush attachment to remove dust and debris from the coils. Replace the base grille and plug the refrigerator back in.

Troubleshooting Guide

Before calling for service, review this section. It may save you time and expense.

Specifications

Warranty and Customer Support

For detailed warranty information, please refer to the warranty card included with your appliance or visit the official KitchenAid website. Keep your proof of purchase for warranty claims.

If you require assistance or service, please contact KitchenAid Customer Service. Have your model number (KSRS25RVMK) and serial number ready when you call.

• Online Support: Visit www.kitchenaid.com/service-and-support
• Telephone Support: Refer to your product registration materials for the appropriate contact number in your region.