Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Skytech 5301P Fireplace Remote Control System. This system is designed to offer safe, reliable, and user-friendly control for gas heating appliances, allowing for both thermostatic and manual operation.
The system utilizes radio frequencies (RF) for communication within a 20-foot range, employing non-directional signals. Each system is factory-programmed with one of 1,048,567 security codes. It is essential to match the remote receiver's code to the transmitter's code before initial use.
The SKY-5301P model includes programmable features, enabling users to set a weekly schedule for their fireplace operation. This system is exclusively for use with gas fireplaces.
Safety Information
Always read and understand all instructions before installing or operating this system. Failure to follow these instructions may result in property damage, personal injury, or loss of life.
- Ensure all wiring is performed by a qualified technician and complies with local codes.
- Do not expose the remote control or receiver to water or excessive humidity.
- Replace batteries promptly when the low battery indicator appears to ensure proper operation.
- This system is designed for gas fireplaces only. Do not use with other heating appliances.
Package Contents
Verify that all components are present before beginning installation:
- 5301P Transmitter (Remote Control)
- Receiver Box
- Wall Plate
- Batteries (4 AA for transmitter, type to be confirmed on receiver unit)
- Installation Instructions (this manual)
Setup and Installation
1. Receiver Installation
The receiver can be installed in various locations:
- In-Wall: Mount the receiver inside a standard electrical wall box.
- On the Hearth: Place the receiver on the hearth near the fireplace.
- Under the Fireplace: Position the receiver behind the control access panel of the fireplace.
Wiring: Connect the receiver to the gas valve of your fireplace. Ensure the fireplace's power supply is off before wiring. The receiver has two terminals; connect them to the appropriate terminals on your gas valve. Consult your fireplace manual for specific wiring diagrams.
Image: The Skytech 5301P system components. This image displays the wall plate with its ON/REMOTE/OFF switch, the handheld remote control with its backlit LCD screen showing temperature and time, and the receiver box with its own ON/REMOTE/OFF switch and wiring terminals.
2. Battery Installation
- Transmitter: Open the battery compartment on the back of the transmitter and insert 4 AA batteries, observing polarity.
- Receiver: Open the battery compartment on the receiver box and insert the required batteries (type to be confirmed on receiver markings), observing polarity.
3. Pairing Transmitter and Receiver (Learning Function)
The transmitter and receiver must be paired to communicate. This process is called "learning."
- Ensure the receiver's slide switch is in the REMOTE position.
- Locate the LEARN button on the receiver. Press and hold the LEARN button until you hear a beep or see an indicator light flash (approximately 1-2 seconds).
- Within 10 seconds, press the PROG button on the transmitter. You should hear a series of beeps from the receiver, indicating successful pairing.
- Test the connection by pressing the touch screen ON or OFF area on the transmitter. The fireplace should respond accordingly.
Operating Instructions
Transmitter Overview
The 5301P transmitter features a backlit LCD touch screen and three control buttons: PROG, MODE, and SET.
- LCD Display: Shows room temperature, set temperature, flame icon (when active), and low battery indicator.
- PROG Button: Used to enter and navigate programming modes.
- MODE Button: Toggles between manual ON/OFF, thermostat mode, and program mode.
- SET Button: Confirms selections and settings.
- Touch Screen Arrows: Used to adjust values (time, temperature) on the LCD.
Setting the Time and Day
- Press and hold the SET button until the time display flashes.
- Use the touch screen arrows to adjust the hour. Press SET to confirm.
- Adjust the minutes using the arrows. Press SET to confirm.
- Adjust the day of the week using the arrows. Press SET to confirm and exit time/day setting.
Manual Operation
To operate the fireplace manually, ensure the receiver's slide switch is in the REMOTE position.
- Press the MODE button until the display shows "ON" or "OFF" (not "THERMO" or "PROG").
- Press the touch screen ON or OFF area to turn the fireplace on or off.
Thermostatic Operation
In thermostatic mode, the fireplace will turn on and off to maintain a set temperature.
- Press the MODE button until the display shows "THERMO".
- The current room temperature and the set temperature will be displayed.
- Use the touch screen arrows to adjust the desired set temperature. The system will automatically activate the fireplace when the room temperature falls below the set temperature and deactivate it when the room temperature rises above the set temperature.
Programmable Operation
The 5301P allows for two programmable periods (P1 and P2) for weekdays (MTWTF) and weekends (SS).
- Press the MODE button until the display shows "PROG".
- Press and hold the PROG button to enter programming mode. The display will show "SS P1" (Weekend Program 1).
- Set P1 ON Time: The time will flash. Use arrows to set the desired ON time for Weekend Program 1. Press SET.
- Set P1 OFF Time: The time will flash. Use arrows to set the desired OFF time for Weekend Program 1. Press SET.
- Set P1 Temperature: The temperature will flash. Use arrows to set the desired temperature for Weekend Program 1. Press SET.
- Repeat steps for "SS P2" (Weekend Program 2), then for "MTWTF P1" (Weekday Program 1), and finally for "MTWTF P2" (Weekday Program 2).
- After setting all programs, press PROG to exit programming mode. Ensure "PROG" is displayed on the main screen to activate the schedule.
Note: If you press PROG or MODE after setting programs, the program setting may be turned off. Always verify "PROG" is visible on the display to confirm scheduled operation.
Maintenance
Battery Replacement
When the low battery indicator appears on the transmitter's LCD, replace all batteries in both the transmitter and receiver promptly. Use fresh alkaline batteries for optimal performance.
- Transmitter: Replace 4 AA batteries.
- Receiver: Replace batteries as indicated on the receiver unit.
After replacing batteries, it may be necessary to re-pair the transmitter and receiver using the "Learning Function" steps described in the Setup section.
Cleaning
Wipe the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fireplace does not respond to remote. |
|
|
| Fireplace turns on/off unexpectedly in THERMO mode. |
|
|
| Programmed schedule is not active. |
|
|
Specifications
- Model: 5301P (Item Model Number: 9800326)
- Brand: SkyTech
- Power Source (Transmitter): 4 AA Batteries
- Power Source (Receiver): Batteries (type to be confirmed on unit)
- Operating Range: Up to 20 feet (non-directional RF)
- Security Codes: 1,048,567 unique codes
- Product Dimensions: 3.5 x 3.6 x 6.4 inches (approximate, for entire system)
- Weight: 1 Pound (approximate, for entire system)
Warranty and Support
Specific warranty details are not provided in the product description. For warranty information and technical support, please contact SkyTech customer service directly. Keep your purchase receipt as proof of purchase.
For further assistance, refer to the manufacturer's official website or contact their support line.
