Technovit Easy 12-Pack Claw Treatment System User Manual

1. Product Overview

The Technovit Easy 12-Pack is a classic and market-leading system for effective claw treatment and rest, successfully utilized for over 15 years. This system employs wooden blocks to provide support and aid in the recovery of animal claws.

Key Features:

• Technovit Original formulation.
• Powder (Model 16220) pre-packaged in 12 individual sachets of 70g each for convenient use.
• Supplied as a complete pack of 12 units.

2. Package Contents

The Technovit Easy 12-Pack typically includes the following components:

• 12 x 70g sachets of Technovit powder (Model 16220).
• Liquid component for mixing.
• Wooden blocks for claw support.
• Mixing cups.
• Mixing spatulas.
• Measuring scoop.

Figure 1: Overview of Technovit claw treatment system components. The image displays a box labeled "Technovit 6091", a large bottle of "1000g Powder", a smaller bottle of "500 ml Liquid", several white mixing cups, wooden blocks, and mixing spatulas, along with a measuring scoop. These components are representative of a Technovit claw treatment kit.

3. Setup and Preparation

1. Ensure a Clean Environment: Prepare a clean, dry, and well-ventilated area for the application.
2. Prepare the Claw: Thoroughly clean and dry the affected claw. Remove any debris, dirt, or moisture. The surface must be completely dry for optimal adhesion.
3. Gather Materials: Have one sachet of Technovit powder, the liquid component, a mixing cup, a mixing spatula, and a wooden block ready.
4. Read Safety Instructions: Always refer to the safety data sheet and product labeling for specific handling precautions, including wearing appropriate personal protective equipment (PPE) such as gloves and eye protection.

4. Operating Instructions

Follow these steps for the correct application of the Technovit Easy system:

1. Mix the Components: Open one 70g sachet of Technovit powder and pour it into a clean mixing cup. Using the provided measuring scoop, add the appropriate amount of liquid component as specified on the product packaging (typically a 2:1 powder to liquid ratio by volume, but always verify).
2. Stir Thoroughly: Use the mixing spatula to thoroughly mix the powder and liquid until a homogeneous, paste-like consistency is achieved. Mix quickly but carefully to avoid incorporating air bubbles. The mixture will begin to set within a few minutes.
3. Apply to Wooden Block: Apply a sufficient amount of the mixed Technovit paste to one side of a wooden block. Ensure even coverage.
4. Attach to Claw: Immediately press the wooden block, with the Technovit paste, firmly onto the prepared, healthy claw. Hold it in place until the adhesive has set sufficiently to secure the block. This typically takes a few minutes, depending on ambient temperature.
5. Allow to Cure: Allow the Technovit to fully cure. The exact curing time will vary based on temperature and humidity, but generally, the animal should be kept off its feet for a short period to ensure complete hardening.
6. Post-Application Care: Monitor the animal and the attached block. The block is designed to wear down or detach naturally over time, typically after several weeks, allowing the injured claw to recover.

5. Maintenance

The Technovit Easy system is designed for single-use application. No specific maintenance of the product components is required after use. Ensure proper disposal of used materials according to local regulations.

Storage:

• Store unused sachets and liquid in a cool, dry place, away from direct sunlight and heat.
• Keep out of reach of children and animals.
• Ensure containers are tightly sealed to prevent contamination or degradation.

6. Troubleshooting

• Problem: Technovit does not set or sets too slowly.

  Possible Cause: Incorrect mixing ratio, low ambient temperature, or expired components.

  Solution: Ensure correct powder-to-liquid ratio. Work in a warmer environment if possible. Check expiration dates of components. Ensure the claw surface is completely dry.
• Problem: Wooden block detaches prematurely.

  Possible Cause: Insufficient cleaning/drying of the claw, inadequate amount of adhesive, or premature weight-bearing.

  Solution: Re-clean and thoroughly dry the claw. Apply a sufficient layer of mixed Technovit. Ensure the animal avoids weight-bearing on the treated claw until the adhesive is fully cured.

• Problem: Skin irritation or allergic reaction.

  Possible Cause: Direct skin contact with components.

  Solution: Always wear appropriate PPE (gloves, eye protection). In case of contact, wash immediately with soap and water. Consult a medical professional if irritation persists.

7. Specifications

8. Warranty and Support

Specific warranty information for the Technovit Easy 12-Pack is not provided in the product details. For warranty claims, technical support, or further inquiries, please contact the manufacturer, Kerbl, directly or refer to their official website.

Manufacturer: Kerbl

Please retain your purchase receipt as proof of purchase for any support inquiries.