ACDelco Tools ANI405

Download PDF
Contents

ACDelco ANI405A Heavy Duty Twin Hammer 1/2" Pneumatic Impact Wrench Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective operation, setup, and maintenance of your ACDelco ANI405A Heavy Duty Twin Hammer 1/2" Pneumatic Impact Wrench. Please read this manual thoroughly before using the tool to ensure proper function and to prevent injury or damage.

The ACDelco ANI405A is a robust pneumatic impact wrench designed for heavy-duty fastening tasks. It features a twin hammer mechanism, delivering up to 500 ft-lbs (677 Nm) of torque. Its compact design and ergonomic handle contribute to ease of use in various professional and automotive applications.

2. Safety Information

Always observe basic safety precautions to reduce the risk of personal injury and damage to the tool. Failure to follow these instructions may result in serious injury.

General Safety Rules:

  • Wear Eye Protection: Always wear ANSI-approved safety goggles or safety glasses with side shields when operating or performing maintenance on the tool.
  • Wear Hearing Protection: Prolonged exposure to noise from pneumatic tools can cause hearing damage. Use appropriate hearing protection.
  • Wear Hand Protection: Use work gloves to protect hands from vibration and potential pinch points.
  • Maintain Proper Air Pressure: Ensure the air supply pressure does not exceed 90 PSI (6.2 Bar). Higher pressures can lead to dangerous operation and tool damage.
  • Disconnect Air Supply: Always disconnect the air supply before changing accessories, performing maintenance, or when the tool is not in use.
  • Keep Work Area Clean: Cluttered work areas and benches can cause accidents. Ensure adequate lighting.
  • Avoid Accidental Starting: Do not carry the tool with your finger on the trigger.
  • Secure Workpiece: Always secure the workpiece in a vise or with clamps to prevent movement during operation.
  • Inspect Tool Before Use: Check for damaged parts, air leaks, or any condition that may affect the tool's operation. Do not use a damaged tool.
  • Use Correct Accessories: Only use impact-rated sockets and accessories designed for impact wrenches.

3. Product Overview

The ACDelco ANI405A impact wrench is designed for efficient and powerful fastening. Familiarize yourself with its components for safe and effective use.

ACDelco ANI405A Impact Wrench front view

Figure 3.1: Front view of the ACDelco ANI405A Impact Wrench. This image shows the overall design of the tool, including the 1/2-inch square drive, the main body, and the trigger mechanism.

ACDelco ANI405A Impact Wrench side view with specifications

Figure 3.2: Side view of the ACDelco ANI405A Impact Wrench. This view highlights the brand logo, model number (ANI405), maximum RPM (8,000), and recommended air pressure (90 PSI / 6.2 Bar) printed on the tool's housing. The 5-speed selector dial is also visible.

ACDelco ANI405A Impact Wrench front and back views

Figure 3.3: Front and back views of the ACDelco ANI405A Impact Wrench. This composite image provides a clear perspective of the tool from both the front (showing the square drive) and the back (showing the air inlet and exhaust).

ACDelco ANI405A Impact Wrench features diagram

Figure 3.4: Diagram illustrating key features of the ACDelco ANI405A Impact Wrench. This graphic highlights the 1/2" square drive, variable speed control, 8,000 RPM free speed, and up to 500 ft-lb torque capacity.

Key Components:

  • 1/2" Square Drive: For attaching impact sockets.
  • Trigger: Activates the tool.
  • Air Inlet: Connection point for the air hose.
  • Forward/Reverse/Speed Selector: A dial or lever to select rotation direction and adjust power output (5-speed settings).
  • Exhaust Port: Releases spent air.

4. Specifications

SpecificationValue
Model NumberANI405A
Square Drive1/2"
Maximum Torque500 ft-lbs (677 Nm)
Standard Bolt Size Capacity5/8" (M16)
Free Speed8,000 RPM
Air Consumption17.7 SCFM (833 liters/sec.)
Overall Length7-1/4" (184 mm)
Air Inlet1/4" NPT
Recommended Air Pressure90 PSI (6.2 Bar)
Recommended Air Hose Size3/8" (10 mm)
Tool Weight5.72 lbs (2.60 kg)
MaterialMetal (Aluminum Housing)
Power SourceAir Powered

5. Setup

Proper setup is crucial for the performance and longevity of your impact wrench.

5.1 Air Supply Connection:

  1. Ensure your air compressor can provide at least 17.7 SCFM at 90 PSI for optimal performance.
  2. Connect a 3/8" (10 mm) air hose to the 1/4" NPT air inlet on the tool. Use thread sealant tape on the air inlet threads to prevent leaks.
  3. Install an in-line air filter/lubricator as close to the tool as possible. This will filter moisture and debris from the air and provide lubrication.
  4. Set the air compressor regulator to 90 PSI (6.2 Bar). Do not exceed this pressure.

5.2 Initial Lubrication:

Before first use, and before each subsequent use, add a few drops of pneumatic tool oil into the air inlet. This lubricates the internal components and extends tool life.

5.3 Attaching Sockets:

Select an impact-rated socket of the correct size for your application. Push the socket firmly onto the 1/2" square drive until it locks into place. Ensure the socket is securely seated before operation.

6. Operating Instructions

Follow these steps for safe and effective operation of your impact wrench.

Mechanic using ACDelco ANI405A Impact Wrench under a car

Figure 6.1: A mechanic using the ACDelco ANI405A Impact Wrench to work on components under a vehicle. This demonstrates the tool's application in automotive repair, highlighting its maneuverability in tight spaces.

Mechanic using ACDelco ANI405A Impact Wrench on a car wheel

Figure 6.2: A mechanic using the ACDelco ANI405A Impact Wrench to remove or install lug nuts on a car wheel. This illustrates a common application for the tool, emphasizing its use for wheel service.

6.1 Selecting Direction and Speed:

The tool features a 5-speed selector for varying torque output. Locate the selector dial on the side of the tool. Rotate the dial to select the desired speed setting (1-5) for forward (tightening) or reverse (loosening) operation. Higher numbers typically indicate higher torque output.

  • Forward (Tightening): Set the selector to the desired speed for tightening fasteners.
  • Reverse (Loosening): Set the selector to the desired speed for loosening fasteners.

6.2 Operating the Tool:

  1. Ensure the air hose is securely connected and the air supply is on.
  2. Place the socket firmly onto the fastener.
  3. Hold the tool with a firm grip, keeping your hands clear of rotating parts.
  4. Press the trigger to activate the tool. The impact mechanism will engage to apply torque.
  5. Release the trigger to stop the tool.

Note: For critical fastening applications requiring precise torque, always use a calibrated torque wrench for final tightening to specification.

7. Maintenance

Regular maintenance ensures optimal performance and extends the life of your ACDelco ANI405A impact wrench.

7.1 Daily Maintenance:

  • Lubrication: Add 5-10 drops of pneumatic tool oil into the air inlet before each use. If using an in-line lubricator, ensure it is filled and adjusted correctly.
  • Air Filter: Check and drain the air filter/water trap daily to remove accumulated moisture.
  • Inspect Air Hoses: Check air hoses for wear, cuts, or leaks. Replace damaged hoses immediately.

7.2 General Cleaning:

Wipe down the tool with a clean, dry cloth after each use. Do not use harsh solvents or abrasive cleaners.

7.3 Storage:

Store the tool in a clean, dry environment when not in use. Disconnect it from the air supply.

8. Troubleshooting

This section addresses common issues you might encounter with your impact wrench.

ProblemPossible CauseSolution
Tool does not operate or has low power.Low air pressure or insufficient air volume.Check air compressor output and regulator setting (should be 90 PSI). Ensure air hose is 3/8" and free of kinks. Verify compressor can deliver 17.7 SCFM.
Lack of lubrication.Add pneumatic tool oil to the air inlet. Check in-line lubricator.
Moisture in air line.Drain air filter/water trap.
Air leaks from tool.Loose fittings or damaged O-rings/seals.Tighten all air fittings. If leaks persist, internal seals may need replacement by a qualified technician.
Excessive vibration.Worn internal components or unbalanced socket.Inspect socket for damage. If tool vibration persists, seek professional service.

9. Warranty and Support

9.1 Warranty Information:

The ACDelco ANI405A Heavy Duty Twin Hammer 1/2" Pneumatic Impact Wrench comes with a 1 Year Limited Warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

9.2 Customer Support:

For technical assistance, parts, or warranty service, please contact ACDelco Tools customer support. Refer to the official ACDelco Tools website or your purchase documentation for current contact information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.