Introduction
This manual provides essential information for the proper use, maintenance, and care of your Nolan N103 N-Com Modular Helmet. Please read it thoroughly before using the helmet to ensure your safety and the longevity of the product.
Image: Front view of the Nolan N103 N-Com Modular Helmet in yellow, showcasing its modular design and clear visor.
Key Features
- VPS (Vision Protection System): Integrated short dark shield for eye protection, independent of the clear shield.
- N-Com Communication System Ready: Designed for easy integration of the N-Com communication system (sold separately).
- Aerodynamic Polycarbonate Shell: Features a built-in spoiler for enhanced stability.
- Pivoting Chinbar: Equipped with a stainless-steel latching mechanism and articulated hinges for modular functionality.
- Dual-action Centromatic Release System: Provides increased safety for chinbar operation.
- Clima-Comfort Interior: Fully removable and washable interior with superior wicking properties and wind-noise reduction.
- Efficient Ventilation: JSW top vent, exhaust grid in the rear spoiler, and chinbar vents for optimal airflow.
- Optically Correct Lexan Faceshield: Quick-change design with UV 400 protection and anti-scratch properties.
- NFR Antifog Insert: Included insert mounts inside the clear shield to prevent fogging.
- Microlock Retention System: Adjustable quick-release system for secure fastening.
Setup and Fitting
1. Sizing and Fit
A properly fitting helmet is crucial for safety. Refer to the size chart to determine the correct helmet size for your head circumference. The helmet should fit snugly around your head without causing pressure points.
Image: A comprehensive size chart displaying various Nolan helmet models and their corresponding head circumferences in centimeters and inches for different sizes (XXS to XXXL).
2. Adjusting the Retention System
The Microlock retention system allows for quick and secure fastening. Insert the tab into the buckle until it clicks. To release, lift the lever and pull the tab out. Ensure the strap is snug under your chin, allowing no more than two fingers to fit between the strap and your chin.
3. N-Com Communication System Installation (Optional)
The N103 helmet is pre-configured for the N-Com communication system. Refer to the N-Com system's specific instruction manual for detailed installation steps. Ensure all components are securely fitted and cables are routed correctly to avoid interference with helmet operation.
Operating the Helmet
1. Opening and Closing the Chinbar
To open the chinbar, locate the dual-action Centromatic release system. Pull the tab on the underside of the chinbar, then squeeze it together with the front tab. This mechanism ensures accidental opening is prevented. Lift the chinbar upwards until it locks into the open position. To close, pull the chinbar down firmly until it clicks securely into place.
2. Operating the VPS (Vision Protection System)
The internal dark shield (VPS) is operated by a slider located on the left side of the helmet. Slide it down to deploy the dark shield for sun protection, and slide it up to retract it. The VPS can be used independently of the clear faceshield.
3. Faceshield Operation and Replacement
The clear Lexan faceshield can be opened and closed by hand. For replacement, use the push-button quick-change mechanism. Press the release buttons on both sides of the faceshield mechanism and carefully detach the shield. Align the new shield with the attachment points and press firmly until it clicks into place. Ensure it is securely fastened before riding.
4. Ventilation System
The helmet features a JSW top vent, chinbar vents, and an exhaust grid in the rear spoiler. These vents are operated by glove-friendly rubber sliders. Open the vents to increase airflow and close them to reduce it, depending on riding conditions.
Maintenance and Care
1. Cleaning the Exterior
Clean the helmet shell with a soft cloth and mild soap and water. Avoid abrasive cleaners, solvents, or petroleum-based products, as these can damage the helmet's finish and materials. Rinse thoroughly and dry with a soft, clean cloth.
2. Cleaning the Interior
The Clima-Comfort interior is fully removable and washable. Detach the interior padding by unsnapping it. Hand wash with mild soap and lukewarm water, or machine wash on a gentle cycle in a laundry bag. Air dry completely before reinserting into the helmet. Do not tumble dry.
3. Faceshield and VPS Care
Clean the faceshield and VPS with a soft, damp cloth and mild soap. Do not use harsh chemicals or abrasive materials. For the NFR antifog insert, follow its specific cleaning instructions, usually a gentle wipe with a soft, damp cloth. Avoid touching the inner surface of the antifog insert directly.
4. Storage
Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from dust and scratches.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Chinbar not locking securely | Debris in locking mechanism; improper closure | Clean mechanism; ensure firm, complete closure until click is heard. |
| Faceshield fogging | High humidity; NFR insert not properly installed or damaged | Ensure NFR insert is clean and correctly seated; open vents for airflow. |
| Excessive wind noise | Vents open; improper fit; worn cheekpads | Close vents; ensure helmet fits snugly; consider replacing worn cheekpads. |
| VPS not sliding smoothly | Dust or debris in slider mechanism | Gently clean around the slider mechanism. Avoid lubricants. |
Specifications
- Model Name: N103
- Manufacturer Part Number: 394405
- Brand: Nolan
- Material: Polycarbonate (PC)
- Shell Type: Hard
- Color: Cab Yellow
- Safety Rating: DOT Certified
- Features: VPS (Vision Protection System), N-Com Ready, Aerodynamic Shell, Pivoting Chinbar, Dual-action Centromatic Release, Removable/Washable Clima-Comfort Interior, Efficient Ventilation, Optically Correct Lexan Faceshield, NFR Antifog Insert, Microlock Retention System.
Warranty and Support
For warranty information and customer support, please refer to the official Nolan website or contact your authorized Nolan dealer. Keep your proof of purchase for any warranty claims. Do not attempt to modify or repair the helmet yourself, as this may void the warranty and compromise safety.
Important: Helmets are designed to absorb impact by partial destruction of the shell and liner. A helmet that has sustained an impact should be replaced, even if no visible damage is apparent.
