Allied Brass WP-90
Allied Brass WP-90 Frameless Round Tilt Beveled Edge Wall Mirror User Manual
Model: WP-90
Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Allied Brass WP-90 Frameless Round Tilt Beveled Edge Wall Mirror. Please read this manual thoroughly before installation and retain it for future reference.
The Allied Brass WP-90 mirror is designed with state-of-the-art simplicity, featuring a frameless 22-inch diameter round mirror with a beveled edge and a durable satin brass finish. Its tilt mechanism allows for optimal viewing angles for users of all heights.
Safety Information
- Always handle glass components with care to prevent breakage and injury.
- Ensure the mounting surface is structurally sound and capable of supporting the mirror's weight (approximately 13.6 pounds).
- Use appropriate tools and safety gear during installation.
- Keep small parts and hardware away from children to prevent choking hazards.
- If you are unsure about any installation step, consult a qualified professional.
Package Contents
Verify that all components are present before beginning installation:
- 1 x Allied Brass WP-90 Frameless Round Tilt Beveled Edge Wall Mirror
- Mounting Hardware (screws, anchors, etc.)
Setup and Installation
The Allied Brass WP-90 mirror features concealed screw mounting hardware for a clean, seamless appearance. Follow these steps for proper installation:
- Choose Location: Select a suitable wall location that can support the mirror's weight and provides adequate space for tilting.
- Mark Mounting Points: Hold the mirror assembly against the wall at the desired height and use a pencil to mark the positions for the mounting brackets. Ensure the marks are level.
- Prepare Wall: Depending on your wall type (drywall, stud, tile), drill pilot holes at the marked locations. Insert wall anchors if necessary.
- Attach Mounting Brackets: Secure the mounting brackets to the wall using the provided screws. Ensure they are firmly attached and level.
- Mount Mirror: Carefully align the mirror's mounting points with the brackets and secure the mirror in place. The concealed screw design will hide the hardware.
- Verify Stability: Gently test the mirror's stability to ensure it is securely mounted and does not wobble.
Figure 1: Front view of the Allied Brass WP-90 Frameless Round Tilt Beveled Edge Wall Mirror. This image shows the round mirror with its beveled edge and the two satin brass mounting points on either side, indicating its wall-mounted design.
Operating Instructions
The WP-90 mirror features a tilt mechanism that allows you to adjust the mirror's angle for optimal viewing. To adjust the tilt:
- Gently grasp the top or bottom edge of the mirror.
- Carefully push or pull the mirror to tilt it upwards or downwards. The pivot points on the mounting hardware allow for smooth adjustment.
- Adjust until the desired angle is achieved. The mirror will hold its position once released.
Maintenance and Care
To ensure the longevity and appearance of your Allied Brass WP-90 mirror, follow these maintenance guidelines:
- Cleaning the Mirror: Use a soft, lint-free cloth and a non-abrasive glass cleaner. Spray the cleaner onto the cloth, not directly onto the mirror, to avoid streaks and protect the brass finish. Wipe gently until clean and dry.
- Cleaning the Brass Finish: For the satin brass components, use a soft, dry cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
- Regular Inspection: Periodically check the mounting hardware to ensure it remains secure. Tighten any loose screws if necessary.
- Avoid Impact: Protect the mirror from direct impact or heavy objects, which could cause chipping or breakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Mirror wobbles after installation. | Mounting hardware not fully tightened or wall anchors not secure. | Ensure all screws are tightened. If using wall anchors, verify they are properly seated. Re-install if necessary. |
| Mirror does not tilt smoothly. | Dust or debris in the pivot mechanism. | Gently clean around the pivot points with a soft, dry cloth. Do not apply lubricants. |
| Streaks on mirror after cleaning. | Too much cleaner used or dirty cloth. | Use less cleaner, apply to cloth first, and use a clean, lint-free cloth. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Allied Brass |
| Model Number | WP-90 |
| Product Dimensions | 22"L x 22"W |
| Shape | Round Tilt |
| Frame Material | Beveled (Frameless) |
| Mounting Type | Wall Mount |
| Finish Type | Satin Brass |
| Material | Metal |
| Item Weight | 13.6 Pounds |
| Assembly Required | No |
| Included Components | Wall Mirror and any required hardware |
| UPC | 013895676397 |
Warranty Information
The Allied Brass WP-90 Frameless Round Tilt Beveled Edge Wall Mirror is provided with a Lifetime Limited Warranty against manufacturer's defects. This warranty covers defects in materials and workmanship under normal use and service.
For detailed warranty terms and conditions, please refer to the official Allied Brass warranty documentation or contact customer support.
Customer Support
If you have any questions, require assistance with installation, or need to report a defect, please contact Allied Brass customer support. For the most up-to-date contact information, please visit the official Allied Brass website or refer to the packaging.
You can also visit the Allied Brass Store on Amazon for more product information and support resources.
Related documentsWP-90
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.