Introduction
The Ansmann Energy 8 Plus is a universal battery charging and maintenance station designed for various rechargeable battery types. This device is capable of charging and maintaining 1-6 AAA or AA cells, 1-4 C or D cells, and 1-2 9V block batteries. It is compatible with NiMH and NiCd rechargeable batteries.
This manual provides essential information on the proper setup, operation, maintenance, and troubleshooting of your Ansmann Energy 8 Plus charger to ensure safe and efficient use.
Image: The Ansmann Energy 8 Plus charger, showcasing its multiple empty charging slots for various battery sizes.
Setup
Unpacking and Initial Inspection
- Carefully remove the Ansmann Energy 8 Plus charger from its packaging.
- Inspect the device for any signs of damage during transit. If any damage is observed, do not use the charger and contact customer support.
- Ensure all components are present: the Ansmann Energy 8 Plus charger unit and its power cable.
Connecting to Power
- Place the charger on a stable, flat, and non-flammable surface, away from direct sunlight or heat sources.
- Connect the power cable to the charger's input port.
- Plug the other end of the power cable into a standard electrical outlet (100-240V AC, 50/60Hz).
- The charger is now ready for use.
Operating Instructions
Inserting Batteries
The Ansmann Energy 8 Plus supports various battery sizes and types. Ensure you are using only NiMH or NiCd rechargeable batteries. Do not attempt to charge non-rechargeable batteries.
- AAA/AA Cells: Insert 1-6 AAA or AA batteries into the designated slots, ensuring correct polarity (+ and -).
- C/D Cells: Insert 1-4 C or D batteries into the larger slots, ensuring correct polarity.
- 9V Block Batteries: Insert 1-2 9V block batteries into the dedicated 9V terminals, ensuring correct polarity.
Image: The Ansmann Energy 8 Plus charger with AAA, AA, C, D, and 9V batteries correctly inserted into their respective charging bays.
The charger features individual monitoring for each battery slot, allowing for simultaneous charging of different battery types and capacities. The device automatically detects defective or incorrectly inserted batteries (e.g., reversed polarity or disposable batteries) and will not attempt to charge them.
Charging Process and Indicators
The Ansmann Energy 8 Plus automatically initiates the charging process upon battery insertion. It includes a refreshing and recharge process, and can even "revive" some damaged batteries.
The charger is equipped with LED indicators for each charging bay to display the status:
- Red LED (Blinking): Indicates a defective battery or incorrect insertion. Remove the battery and check.
- Red LED (Solid): Battery is currently charging.
- Green LED (Solid): Charging is complete, and the charger has switched to trickle charge mode to maintain the battery's full capacity.
The charger incorporates multiple overcharging protection mechanisms and automatically completes the charging process, switching to trickle charge to prevent battery damage.
Image: The Ansmann Energy 8 Plus charger actively charging batteries, with visible LED indicators showing charging status.
Maintenance
Cleaning the Charger
- Always unplug the charger from the power outlet before cleaning.
- Use a soft, dry cloth to wipe the exterior of the charger.
- Do not use liquid cleaners, abrasive pads, or chemical solvents, as these can damage the device.
- Ensure no dust or debris accumulates in the battery slots. Use a soft brush or compressed air if necessary.
Storage
- When not in use, store the charger in a cool, dry place, away from direct sunlight and extreme temperatures.
- It is recommended to unplug the charger when not in use for extended periods, as the internal power supply may remain slightly warm.
Troubleshooting
If you encounter issues with your Ansmann Energy 8 Plus charger, please refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger not powering on. | No power supply; loose connection. | Ensure the power cable is securely plugged into both the charger and the wall outlet. Check if the outlet is functional. |
| Red LED blinking for a battery. | Defective battery; incorrect battery type (non-rechargeable); reversed polarity. | Remove the battery and re-insert it with correct polarity. Ensure it is a NiMH or NiCd rechargeable battery. If the LED still blinks, the battery may be defective and should be replaced. |
| Batteries not charging or taking too long. | Battery capacity too high for charging current; very deeply discharged battery. | Allow more time for charging, especially for high-capacity batteries. The charger may be performing a refreshing cycle for deeply discharged batteries. |
| Charger feels warm during operation. | Normal operation; insufficient ventilation. | It is normal for the charger to become warm during charging. Ensure it is placed on a hard, flat surface with adequate ventilation. If it becomes excessively hot, unplug it immediately and contact support. |
If the problem persists after attempting these solutions, please contact Ansmann customer support.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 8 x 3 x 10.5 inches |
| Item Weight | 1.33 pounds (605 Grams) |
| Manufacturer | Ansmann USA Corporation |
| Model Number | 5207442/US |
| Compatible Battery Types | NiMH/NiCd rechargeable batteries |
| Supported Battery Sizes | AAA, AA, C, D, 9V |
| Charging Currents | 1000mA (AA, C, D), 400mA (AAA), 60mA (9V) |
| Output Voltage | 1.2 Volts |
| Color | Blue |
| Date First Available | July 9, 2010 |
Image: The Ansmann Energy 8 Plus charger connected and in use amidst various electronic testing equipment, highlighting its professional application.
Warranty Information
The Ansmann Energy 8 Plus charger typically comes with a manufacturer's warranty. Based on available information, Ansmann products often include a 3-year warranty. Please refer to the original product packaging or the official Ansmann website for the most accurate and up-to-date warranty terms and conditions specific to your region.
Keep your purchase receipt as proof of purchase for any warranty claims.
Image: The retail packaging for the Ansmann Energy 8 Plus charger, displaying product features and a "3 Jahre Warranty" (3 Years Warranty) badge.
Support and Contact
For further assistance, technical support, or warranty inquiries, please contact Ansmann customer service.
- Official Website: Visit the Ansmann official website for product information and support contacts.
- User Manual (PDF): A detailed PDF version of the user manual is available for download: Download User Manual.
- Manufacturer: Ansmann USA Corporation
When contacting support, please have your product model number (5207442/US) and purchase details ready.