1. Introduction
This manual provides detailed instructions for installing the Scosche HA1710B Double DIN Radio Install Dash Kit. This kit is designed to facilitate the installation of an aftermarket car stereo into select 2001-05 Honda Civic vehicles, providing a factory-like appearance.
Please read all instructions carefully before beginning the installation process. Ensure all necessary tools and components are available.
2. Compatibility
This dash kit is compatible with select 2001-05 Honda Civic models. It is not compatible with Civic Si models.
For specific compatibility, refer to the fit guide image below. This kit is designed for Double DIN installations only.
Image: Fit Guide for Scosche HA1710B Dash Kit. This guide illustrates vehicle compatibility, specifically noting that the kit works with 2001-05 Honda Civic DX, LX, and EX models, but is not for use with Civic Si models. It also indicates that it is for Double DIN installations only.
Scosche Double DIN Kits accommodate True Double DIN stereos with a maximum faceplate opening of 96.8mm x 173mm. Some radios labeled as Double DIN may be oversized, potentially requiring minor trimming of the kit for a proper fit.
Image: Industry Standard Sized Opening. This diagram provides the dimensions for the stereo opening in the dash kit, which are 96.8mm (3-13/16 inches) in height and 173mm (6-13/16 inches) in width. This is for reference to ensure your aftermarket stereo will fit.
3. Package Contents
Verify that all items listed below are included in your package:
- Radio Bezel (Dash Kit)
- Instruction Manual
- Mounting Brackets (Left and Right)
- Hardware (screws, clips)
Image: Scosche HA1710B Dash Kit. This image displays the primary dash kit bezel, which frames the aftermarket stereo.
Image: Angled view of the Scosche HA1710B Dash Kit. This perspective highlights the design and mounting tabs of the dash kit bezel.
Image: Car Stereo Dash Kit Components. This image shows the dash kit along with representations of a wire harness and antenna adapter, noting that the latter two are sold separately.
4. Safety Information
- Always disconnect the vehicle's negative battery terminal before beginning any electrical work to prevent short circuits and electrical shock.
- Wear appropriate personal protective equipment, such as safety glasses.
- Ensure the vehicle is parked on a level surface with the parking brake engaged.
- Refer to your vehicle's service manual for specific instructions on removing factory components.
- If you are unsure about any step, consult a qualified professional installer.
5. Installation
The following video provides a comprehensive overview of the installation process, from preparation to final testing. Detailed steps are also provided below.
Video: Scosche Stereo Installation. This video demonstrates the general process of installing a Scosche stereo kit, including disconnecting the battery, preparing the dash kit components by removing unnecessary tabs, installing the new stereo into the dash kit, removing the factory stereo, making wiring connections, plugging in harnesses, installing the new stereo into the dash, reconnecting the battery, and testing the radio.
5.1. Preparation
- Disconnect Battery: Disconnect the negative battery terminal of your vehicle.
- Review Instructions: Read through the entire instruction manual provided with the dash kit and your new stereo.
- Identify Tabs: After reviewing the instructions, identify and remove any tabs on the dash kit components that are not required for your specific application.
5.2. Factory Radio Removal
- Remove Trim Panels: Using a panel removal tool, carefully pry off and remove any trim panels surrounding your factory stereo.
- Unscrew Factory Radio: Locate and unscrew the mounting screws holding the factory radio in place.
- Unplug Harnesses: Gently pull out the factory radio and unplug all electrical harnesses and antenna cables from the back.
5.3. Wiring Connections
Connect the aftermarket stereo's wiring harness to the vehicle's wiring harness. Match wire colors according to the instructions provided with your aftermarket stereo and the Scosche wiring adapter (if purchased separately).
- Use splice connectors or solder connections for secure and reliable electrical contact.
- Ensure all connections are properly insulated with electrical tape or heat shrink tubing.
- Some wires, such as amplifier turn-on, parking brake sense, and steering wheel control connections, may require specific routing or additional adapters not included in this kit.
5.4. Dash Kit Assembly
- Attach Brackets: Secure the left and right mounting brackets to your new aftermarket stereo using the screws provided with the stereo.
- Insert Stereo: Slide the assembled stereo and brackets into the dash kit bezel.
5.5. New Stereo Installation
- Connect Wiring: Plug the vehicle's wiring harness into the aftermarket stereo's harness. Connect the antenna cable.
- Mount Stereo: Carefully slide the new stereo assembly into the dashboard opening. Secure it with the factory mounting screws.
- Reinstall Trim: Reattach all removed trim panels, ensuring they snap securely into place.
5.6. Final Steps
- Reconnect Battery: Reconnect the negative battery terminal.
- Test Functions: Turn on the vehicle and test all functions of the new stereo, including audio, radio, and any connected accessories.
6. Operation
This dash kit provides the mounting solution for your aftermarket stereo. For detailed operating instructions of your new stereo, please refer to the instruction manual provided by the stereo manufacturer.
7. Maintenance
- Periodically check the mounting screws for tightness.
- Clean the dash kit and stereo faceplate with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners.
- Ensure no debris accumulates around the stereo or in the dash opening.
8. Troubleshooting
- Stereo does not power on:
- Check battery connections.
- Verify all wiring harness connections are secure and correct.
- Check the stereo's fuse.
- Poor fit of stereo in dash kit:
- Ensure all unnecessary tabs on the dash kit were removed.
- Confirm your aftermarket stereo's dimensions are within the kit's specifications (96.8mm x 173mm). Minor trimming may be required for oversized units.
- Verify factory radio brackets are used as required.
- Dash kit does not fit vehicle:
- Double-check vehicle compatibility (2001-05 Honda Civic, non-Si models).
- Ensure all factory components were removed correctly.
9. Specifications
| Model Number | HA1710B |
| Product Dimensions | 1.5 x 6.5 x 13.25 inches |
| Item Weight | 1.6 ounces |
| Color | Black |
| Material | OEM Quality Materials (ABS Plastic) |
| Compatibility | Select 2001-05 Honda Civic (DX, LX, EX models) |
| Stereo Type | Double DIN (Max faceplate opening: 96.8mm x 173mm) |
10. Warranty and Support
The Scosche HA1710B Dash Kit is backed by Scosche's Limited Lifetime Warranty and Lifetime Tech Support.
For technical assistance or warranty claims, please contact Scosche customer support directly. Refer to the official Scosche website or product packaging for contact information.
