1. Introduction
The Winegard CE-1000 is a single cable entry plate designed to provide a secure and weather-resistant pass-through for a single coaxial or other low-voltage cable through a wall or roof. This plate is ideal for RVs, marine applications, and other installations where a clean and protected cable entry point is required. It helps prevent water intrusion and maintains the integrity of the mounting surface.
2. Safety Information
- Always wear appropriate personal protective equipment (PPE) such as safety glasses and gloves when handling tools and performing installation.
- Ensure the installation area is free from electrical hazards before drilling or cutting.
- Use caution when working on elevated surfaces, such as RV roofs.
- Properly seal all openings and screw holes with a marine-grade or RV-grade sealant to prevent water damage. Failure to do so can lead to serious structural damage.
- Do not overtighten screws, as this may strip threads or crack the plate.
3. Package Contents
Verify that all components are present before beginning installation:
- 1x Winegard CE-1000 Single Cable Entry Plate (White)
- Mounting Screws
Image 1: Winegard CE-1000 Single Cable Entry Plate with included mounting screws. The plate is white, rectangular with rounded corners, and features a raised channel for cable routing. Eight gold-colored screws are shown alongside the plate.
4. Setup and Installation
Follow these steps for proper installation of your Winegard CE-1000 Cable Entry Plate:
- Select Location: Choose a flat, clean, and dry surface for mounting the cable entry plate. Ensure there is sufficient clearance on both sides of the mounting surface for cable routing and access.
- Prepare Surface: Clean the mounting surface thoroughly to remove any dirt, grease, or old sealant. The surface must be completely dry before proceeding.
- Mark Pilot Holes: Position the CE-1000 plate in the desired location. Use a pencil or marker to mark the positions for the mounting screws and the cable entry hole.
- Drill Holes: Carefully drill pilot holes for the mounting screws. Drill a larger hole for the cable pass-through, ensuring it is just large enough for your cable to fit through without excessive play. Deburr any sharp edges.
- Route Cable: Feed your single cable through the drilled hole and position it within the channel of the CE-1000 plate.
- Apply Sealant: Apply a generous bead of approved RV or marine-grade self-leveling sealant around the cable entry hole and around the perimeter of the plate's underside where it will contact the mounting surface. Also, apply sealant into each screw pilot hole.
- Mount Plate: Carefully align the plate with the pilot holes and press it firmly into the sealant. Insert and hand-tighten the mounting screws until snug. Do not overtighten.
- Final Sealing: Apply another bead of sealant over the heads of the mounting screws and around the entire perimeter of the installed plate, ensuring a watertight seal. Also, seal around the cable where it exits the plate's channel. Allow the sealant to cure according to the manufacturer's instructions.
5. Operating Instructions
Once installed, the Winegard CE-1000 operates passively by providing a sealed entry point for your cable. Ensure the cable is properly routed through the plate's channel and that all sealant has cured. No further operational steps are required for the plate itself.
6. Maintenance
- Regular Inspection: Periodically inspect the cable entry plate and surrounding sealant for any signs of cracking, peeling, or degradation, especially after extreme weather conditions.
- Cleaning: Clean the plate with mild soap and water as needed. Avoid abrasive cleaners that could damage the material or sealant.
- Re-sealing: If any signs of sealant failure are observed, promptly clean the affected area and apply fresh sealant to maintain a watertight seal.
- Screw Tightness: Occasionally check the mounting screws for tightness. If loose, gently tighten them and re-apply sealant over the screw heads if necessary.
7. Troubleshooting
Most issues related to the cable entry plate involve water intrusion. Here are common troubleshooting steps:
- Water Leakage: If water is observed near the cable entry point, the sealant has likely failed.
- Inspect the entire perimeter of the plate and around the cable for cracks or gaps in the sealant.
- Clean the area thoroughly, remove any loose or degraded sealant.
- Apply fresh, appropriate sealant generously to all affected areas, ensuring complete coverage.
- Loose Plate: If the plate feels loose, the mounting screws may have come undone or the material they are screwed into has degraded.
- Gently tighten the mounting screws. If they spin freely, the pilot holes may be stripped. Consider using slightly larger screws or relocating the plate if possible.
- Always re-seal screw heads and the plate perimeter after tightening.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | CE-1000 |
| Brand | Winegard |
| Color | White |
| Material | Durable, Water-Resistant Material (Note: Some specifications may incorrectly list 'Ceramic' due to data discrepancies; the product is designed for outdoor use.) |
| Product Dimensions | 6.5 x 4 x 0.01 inches (approximate) |
| Item Weight | 0.4 ounces |
| Cable Capacity | Single Cable |
| Included Components | Plate and Screws |
9. Warranty Information
This Winegard product is covered by the manufacturer's standard warranty. For specific details regarding warranty coverage, duration, and terms, please refer to the documentation included with your purchase or visit the official Winegard website. Keep your proof of purchase for warranty claims.
10. Support
For technical assistance, installation questions, or to report any issues with your Winegard CE-1000 Single Cable Entry Plate, please contact Winegard Customer Support. You can typically find contact information, including phone numbers and support portals, on the official Winegard website (www.winegard.com).
