Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your aFe Power Takeda Intake Replacement Air Filter with Pro Dry S Media. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.
Image: The aFe Power Takeda Intake Replacement Air Filter, featuring a conical design. The filter media is a light grey, indicating the Pro Dry S material, and it is encased by black plastic rings at the top and bottom. This filter is designed for dry filtration, requiring no oil.
Product Overview
The aFe Power Takeda Intake Replacement Air Filter (Model TF-9004D) is engineered to provide superior filtration and airflow for your vehicle's intake system. It features a Pro Dry S media, which is a synthetic, oil-free filter material designed for convenience and efficiency. This filter is washable and reusable, offering a long-term solution for air filtration.
- Type: Pro DRY S
- Filter Shape: Round (Conical)
- Filter Color: Blue (Note: The product description states blue, but the image shows grey filter media.)
- Inlet Size: 3.50 inches
- Height: 5 inches
Installation
Before beginning installation, ensure your vehicle's engine is cool and the ignition is off. Refer to your vehicle's service manual for specific instructions regarding the removal of the existing air filter and access to the intake system.
- Preparation: Locate the air intake box or existing air filter assembly in your vehicle.
- Removal of Old Filter: Carefully remove the clamps, screws, or clips securing the existing air filter. Extract the old filter from its housing.
- Housing Inspection: Inspect the air filter housing for any debris, dust, or foreign objects. Clean the housing thoroughly if necessary.
- Installation of New Filter: Insert the aFe Power Takeda Replacement Air Filter into the housing, ensuring it is seated correctly and securely. The conical shape should fit snugly within the designated space.
- Secure Filter: Re-attach all clamps, screws, or clips that were removed earlier, ensuring the filter is firmly held in place and there are no air leaks.
- Final Check: Double-check all connections and ensure all tools are removed from the engine bay before starting the vehicle.
Note: Professional installation is recommended if you are unfamiliar with automotive maintenance procedures.
Maintenance
The Pro Dry S filter media is designed for easy maintenance and does not require oiling. Regular cleaning will ensure optimal performance and extend the life of your filter.
Cleaning Procedure:
- Removal: Carefully remove the air filter from your vehicle's intake system following the reverse of the installation steps.
- Pre-Cleaning: Gently tap the filter against a hard surface to dislodge any loose dirt and debris. You may also use compressed air (from the clean side out) to remove larger particles, but use low pressure to avoid damaging the media.
- Washing: Use a mild detergent or a specialized air filter cleaning solution mixed with water. Submerge the filter and gently agitate it to loosen embedded dirt. Rinse the filter thoroughly with low-pressure water from the clean side out until the water runs clear.
- Drying: Allow the filter to air dry completely before reinstallation. Do not use heat guns, direct sunlight, or compressed air at high pressure, as this can damage the filter media. Drying time may vary depending on environmental conditions.
- Reinstallation: Once completely dry, reinstall the filter into your vehicle's intake system as described in the Installation section.
Important: Do not use oil on this filter. The Pro Dry S media is designed to function without oil. Oiling this filter can impede its performance and potentially damage your vehicle's sensors.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced Engine Performance | Clogged or dirty air filter. | Clean the air filter as per the Maintenance section. |
| Check Engine Light On | Improperly installed filter causing air leaks or sensor issues. | Re-check filter installation for proper seating and secure connections. Ensure no oil was applied to the filter. Consult a professional if the light persists. |
| Unusual Noises from Intake | Loose filter or intake components. | Verify all clamps and connections are tight and secure. |
Specifications
- Product Grade: Replacement Part
- Brand: aFe Power
- Model Number: TF-9004D
- Shape: Conical
- Filter Type: Pro DRY S (Dry, Oil-Free)
- Inlet Diameter: 3.50 inches
- Height: 5 inches
- UPC: 802959529041
- ASIN: B003EOVMMY
- Date First Available: March 31, 2010
Warranty and Support
For specific warranty information and customer support, please refer to the official aFe Power website or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Website: www.afepower.com
Contact: Refer to the website for contact details.
