User Manual
Bunker Hill Security Battery Operated LED Motion Sensor Light
Model: 95276
Introduction
This manual provides instructions for the proper setup, operation, and maintenance of your Bunker Hill Security Battery Operated LED Motion Sensor Light, Model 95276. This device is designed to provide illumination in areas without electrical outlets, such as sheds, closets, and stairwells, offering both convenience and security.
The light features a super bright LED lamp and a three-way switch for continuous, automatic (motion-activated), or off operation, allowing for energy saving in auto mode.
Figure 1: Front view of the Bunker Hill Security Battery Operated LED Motion Sensor Light, showing the light panel and motion sensor lens.
Safety Information
- Read all instructions before use.
- Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
- Dispose of used batteries properly according to local regulations.
- Do not expose the unit to extreme temperatures or moisture.
- This product is intended for indoor use or sheltered outdoor locations where it will not be directly exposed to weather elements.
Package Contents
- 1 x Bunker Hill Security Battery Operated LED Motion Sensor Light (Model 95276)
- User Manual
- Note: Four AA batteries are required for operation and are not included.
Setup
1. Battery Installation
- Locate the battery compartment cover on the back of the unit.
- Slide or unclip the cover to open the compartment.
- Insert four (4) AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
- Replace the battery compartment cover securely.
2. Mounting and Placement
The light can be placed on a flat surface or mounted to a wall. Consider the following for optimal performance:
- Choose a location where the motion sensor will have an unobstructed view of the area you wish to monitor.
- Avoid placing the light near heat sources or in direct sunlight, as this may affect sensor performance.
- For wall mounting, use appropriate screws (not included) to secure the unit through the designated mounting holes on the back.
Operating Instructions
The Bunker Hill Security LED Motion Sensor Light features a three-way switch located on the unit. This switch controls the operating mode:
- OFF: In this position, the light is completely off and will not activate.
- ON (Continuous): In this position, the light will remain continuously illuminated, regardless of motion or ambient light conditions.
- AUTO: In this position, the light will activate automatically when motion is detected within its range, provided the ambient light is low enough. The light will turn off automatically after a period of no motion. This mode is designed to save energy.
Select the desired mode by sliding the switch to the corresponding position.
Maintenance
Battery Replacement
When the light begins to dim or stops functioning, it is time to replace the batteries. Follow the battery installation steps outlined in the Setup section.
Cleaning
To clean the unit, wipe it with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or internal components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Batteries are dead or incorrectly installed. 2. Switch is in the 'OFF' position. 3. Ambient light is too bright (in 'AUTO' mode). | 1. Replace batteries and ensure correct polarity. 2. Slide switch to 'ON' or 'AUTO'. 3. Test in a darker environment. |
| Light stays on continuously (in 'AUTO' mode). | 1. Switch is in the 'ON' position. 2. Continuous motion detected within sensor range. | 1. Slide switch to 'AUTO'. 2. Relocate the light to an area with less constant activity or adjust its angle. |
| Light is dim. | Batteries are low. | Replace all four AA batteries. |
Specifications
- Brand: Bunker Hill Security
- Model: 95276
- Power Source: 4 x AA Batteries (not included)
- Bulb Type: LED
- Wattage: 5 watts
- Special Features: Motion-Sensor, Three-way switch (OFF/ON/AUTO)
- Material: Hard Plastic
- Color: White
- Item Weight: 3.2 ounces
- Overall Dimensions: 1-5/8" L x 3-1/4" W x 4-5/8" H
Warranty and Support
Specific warranty information and customer support contact details are not provided in the product description. Please refer to the product packaging or the retailer where the item was purchased for warranty terms and support options.
