1. Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Pentair 123326 4-inch Submersible Well Pump. Please read this manual thoroughly before installation or operation to ensure proper use and to prevent potential hazards.
The Pentair 123326 is a 1 hp, 230V, 2-wire submersible well pump designed for wells up to 300 feet deep, delivering a flow rate of 10 gallons per minute (GPM). It features a patented floating stack design for enhanced sand resistance and reduced sand locking, along with corrosion-resistant stainless steel pump and motor housing. The pump includes a 1-1/4 inch discharge connection and precision molded impellers and diffusers, with a built-in check valve for reliable performance.
2. Safety Information
WARNING: Always disconnect power before servicing the pump or well system. Failure to do so can result in serious injury or death from electrical shock.
CAUTION: This pump is designed for pumping clean water only. Pumping flammable, corrosive, or abrasive liquids can damage the pump and void the warranty.
- Ensure all electrical connections are made by a qualified electrician and comply with local codes.
- Proper grounding is essential to prevent electrical shock.
- Do not operate the pump dry. Dry running can cause severe damage to the pump.
- Wear appropriate personal protective equipment (PPE) during installation and maintenance.
3. Setup and Installation
Before beginning installation, ensure you have all necessary tools and materials, including appropriate piping, electrical wiring, and safety equipment. The pump is designed for a 4-inch well casing.
3.1 Pre-Installation Checks
- Verify the well depth and diameter are suitable for the 4-inch submersible pump.
- Confirm power supply matches pump requirements (230V, 2-wire).
- Inspect the pump for any visible damage from shipping.
3.2 Electrical Connection
Connect the pump to a dedicated 230V, 2-wire electrical circuit. Ensure proper wire sizing for the distance from the control box to the pump. All connections must be waterproof and sealed to prevent moisture ingress.
3.3 Plumbing Connection
Attach the discharge pipe to the pump's 1-1/4 inch discharge connection. Use appropriate thread sealant to ensure a watertight seal. Install a check valve if not already integrated, though this model features a built-in check valve.
3.4 Lowering the Pump
Carefully lower the pump into the well using a safety rope or cable attached to the pump's lifting eye. Ensure the pump hangs freely and does not touch the bottom or sides of the well casing. Maintain proper clearance from the well bottom to avoid drawing in sediment.

An image showing the Pentair 123326 4-inch Submersible Well Pump, featuring its stainless steel housing and compact design. This pump is designed for deep well applications.
4. Operating Instructions
Once the pump is fully installed and all connections are secure, the system can be energized. The pump will begin to draw water from the well and deliver it to the surface at a rate of up to 10 GPM.
- Ensure the pressure tank is properly charged and connected to the system.
- Open a faucet to allow air to escape the system during initial startup.
- Monitor the pressure gauge to ensure the pump is operating within its specified pressure range.
- Avoid frequent on/off cycling, which can reduce pump lifespan.
5. Maintenance
The Pentair 123326 pump is designed for minimal maintenance due to its durable stainless steel construction and patented floating stack design for sand resistance. However, periodic checks are recommended to ensure optimal performance and longevity.
- Annual System Check: Have a qualified professional inspect the entire well system annually, including the pump, wiring, pressure tank, and controls.
- Water Quality: Monitor water quality. Excessive sediment or unusual changes may indicate issues with the well or pump.
- Electrical Connections: Periodically check electrical connections for corrosion or loose wiring (ensure power is disconnected first).
- Pressure Tank: Verify the pressure tank's air charge is correct according to its manufacturer's instructions.
6. Troubleshooting
This section provides solutions to common issues you might encounter with your submersible well pump. For problems not listed here, or if solutions do not resolve the issue, contact a qualified pump technician.
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not run | No power; tripped breaker; faulty control box; motor issue. | Check power supply and breaker. Inspect control box. Consult electrician for motor diagnosis. |
| Low water pressure/flow | Partially clogged pump/pipe; low well yield; pressure tank issue; worn impellers. | Check for obstructions. Verify well water level. Inspect pressure tank. Professional inspection may be needed. |
| Pump cycles frequently | Leaking plumbing; faulty pressure switch; waterlogged pressure tank. | Check for leaks. Test/replace pressure switch. Recharge or replace pressure tank. |
| No water delivered | Well dry; pump air-locked; broken pipe; pump failure. | Check well water level. Bleed air from system. Inspect plumbing. Contact professional. |
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | Pentair |
| Model Number | 123326 |
| Horsepower (HP) | 1 hp |
| Voltage | 230V |
| Wire Configuration | 2 Wire |
| Maximum Flow Rate | 10 Gallons Per Minute (GPM) |
| Well Depth Capacity | Up to 300 feet |
| Pump Diameter | 4 inches |
| Material | Stainless Steel |
| Discharge Connection | 1-1/4 inch |
| Item Weight | 37 Pounds |
| Product Dimensions | 1 x 4.5 x 38 inches |
| Special Features | Patented floating stack design for sand resistance, built-in check valve, precision molded impellers & diffusers. |
8. Warranty and Support
For detailed warranty information and technical support, please refer to the official Pentair website or contact Pentair customer service. Keep your purchase receipt as proof of purchase for warranty claims.
You can also visit the official Pentair store for more information and products: Pentair Store on Amazon