1. Introduction
The Elation Professional SDC-6 v2 is a compact and versatile 6-channel DMX controller designed for easy operation of DMX-compatible lighting fixtures. It features six individual channel faders and one master fader, providing intuitive control over various lighting effects. This manual provides essential information for the safe and efficient use of your SDC-6 v2 controller, including setup, operation, maintenance, and troubleshooting.
2. Safety Instructions
Please read these safety instructions carefully before operating the device. Failure to comply may result in damage to the unit, property, or personal injury.
- Always connect the device to a grounded power outlet.
- Ensure the power adapter's voltage matches the local power supply.
- Do not expose the unit to rain, moisture, or excessive humidity.
- Avoid placing the unit near heat sources or in direct sunlight.
- Do not operate the unit if the power cord is damaged.
- Refer all servicing to qualified service personnel. There are no user-serviceable parts inside.
- Disconnect power before cleaning or performing any maintenance.
3. Package Contents
Verify that all items listed below are present and in good condition upon opening the package:
- Elation Professional SDC-6 v2 DMX Controller
- 9V Power Adapter
- User Manual (this document)
4. Setup
Follow these steps to set up your SDC-6 v2 DMX controller:
- Placement: Place the controller on a stable, flat surface away from excessive heat, moisture, or dust.
- DMX Connection: Connect the 3-pin DMX output connector of the SDC-6 v2 to the DMX input of your first DMX-compatible lighting fixture. If you have multiple fixtures, daisy-chain them by connecting the DMX output of the first fixture to the DMX input of the second, and so on.
- Power Connection: Insert the 9V power adapter into the power input jack on the controller. Plug the power adapter into a suitable electrical outlet. The power indicator LED on the controller should illuminate.
Figure 4.1: Top view of the Elation SDC-6 v2 DMX Controller, showing the six channel faders, master fader, and power indicator.
Figure 4.2: Side view of the Elation SDC-6 v2 DMX Controller, illustrating the battery compartment for optional portable power (battery not included for primary operation).
5. Operating Instructions
The SDC-6 v2 provides straightforward control over your DMX lighting fixtures.
5.1. Channel Faders (1-6)
Each of the six numbered faders (1 through 6) corresponds to a DMX channel. Moving a fader up increases the DMX value for that channel (from 0 to 255), while moving it down decreases the value. The specific function of each channel (e.g., dimmer, color, strobe) depends on the DMX address and mode settings of your connected lighting fixture.
5.2. Master Fader
The Master fader controls the overall output level of all active DMX channels. Moving the Master fader down will dim or turn off all lights controlled by the individual channel faders, regardless of their individual settings. Moving it up will restore the output to the levels set by the individual channel faders.
5.3. Power Indicator
The Power indicator LED illuminates when the unit is receiving power, indicating it is ready for operation.
6. Maintenance
Proper maintenance ensures the longevity and reliable operation of your SDC-6 v2 controller.
- Cleaning: Use a soft, dry cloth to wipe the exterior of the unit. Do not use abrasive cleaners, solvents, or harsh chemicals.
- Storage: When not in use for extended periods, store the controller in a cool, dry place, protected from dust and extreme temperatures.
- Power: Always disconnect the power adapter when the unit is not in use or before cleaning.
7. Troubleshooting
If you encounter issues with your SDC-6 v2 controller, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power indicator light | Power adapter not connected or faulty; power outlet not active. | Ensure power adapter is securely connected to the unit and a working outlet. Test the outlet with another device. |
| Lights not responding to faders | Incorrect DMX connection; Master fader is down; DMX address mismatch on fixtures; fixture not in DMX mode. | Check DMX cable connections. Ensure Master fader is up. Verify DMX addresses on fixtures match the channels being controlled. Confirm fixtures are set to DMX mode. |
| Intermittent control | Loose DMX cable connection; DMX signal interference. | Secure all DMX cable connections. Use high-quality DMX cables. Avoid running DMX cables parallel to power cables. |
8. Specifications
| Model | SDC6 |
| Brand | Elation Professional (ADJ) |
| Channels | 6 DMX Channels + 1 Master Fader |
| DMX Connector | 3-pin XLR DMX Output |
| Power Supply | 9V DC (via included power adapter) |
| Dimensions (L x W x H) | 173 mm x 153 mm x 55 mm (6.81 in x 6.02 in x 2.17 in) |
| Weight | 1 kg (2.2 lbs) |
| Color | Black |
| Country of Origin | China |
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Elation Professional website. Keep your proof of purchase for warranty claims.
For further assistance, you may contact the seller or manufacturer directly. Contact details are typically available on their respective websites or on your purchase invoice.
