BELL 2-Gang Weatherproof Box (Model 5348-0) Instruction Manual

Introduction

This manual provides comprehensive instructions for the safe and proper installation, operation, and maintenance of your BELL 2-Gang Weatherproof Box, Model 5348-0. Please read all instructions carefully before beginning any work to ensure safety and optimal performance of the product.

Safety Information

WARNING: Risk of electric shock. Improper installation or use can lead to serious injury or death. Always follow local electrical codes and consult a qualified electrician if you are unsure about any part of the installation process.

• Always disconnect power at the circuit breaker or fuse box before installing or servicing this product.
• Ensure all connections are secure and properly insulated.
• This product is designed for outdoor use and must be installed in accordance with all applicable electrical codes for wet locations.
• Use only approved fittings and conduit with the threaded outlets.
• Ensure the ground screw is properly connected to the electrical system's ground.

Product Overview

The BELL 2-Gang Weatherproof Box (Model 5348-0) is a durable enclosure designed for electrical installations in outdoor or wet environments. Constructed from rugged die-cast aluminum, it features a powder-coated finish for enhanced weatherability and scratch resistance.

Key Features:

• Rugged die-cast aluminum construction for durability.
• State-of-the-art powder coat finish for maximum weatherability and scratch resistance.
• Seven 3/4 inch threaded outlets for versatile conduit connections.
• Eight box mounting options with detachable lugs for flexible installation.
• Internal hub threads comply with NEMA requirements.
• Pre-installed ground screw for safety.

Components:

• 2-Gang Weatherproof Box (Model 5348-0)
• Two 3/4 inch closure plugs
• Ground screw (pre-installed)
• Detachable mounting lugs

Setup and Installation

Before You Begin:

• Ensure power is disconnected at the main electrical panel.
• Gather necessary tools: screwdriver, wire strippers, conduit wrench, sealant, drill, mounting hardware (screws/anchors).
• Verify the installation location is suitable for a weatherproof electrical box.

Mounting the Box:

1. Position the weatherproof box at the desired mounting location. The box offers eight mounting options, including detachable lugs for flexibility.
2. Mark the drilling points through the mounting holes.
3. Drill pilot holes appropriate for your mounting hardware.
4. Securely fasten the box to the surface using appropriate screws or anchors. Ensure the box is level and firmly attached.

Wiring Connections:

1. Route electrical conduit into the desired 3/4 inch threaded outlets. The internal hub threads are NEMA compliant.
2. Securely tighten all conduit fittings to ensure a weatherproof seal.
3. Connect the ground wire to the pre-installed green ground screw inside the box.
4. Make all necessary electrical connections for your devices (e.g., outlets, switches) within the box, following local electrical codes.

Sealing Unused Outlets:

The box includes two 3/4 inch closure plugs. For rain tightness, any unused threaded outlets must be sealed with these plugs and a silicone sealing compound. Apply sealant around the threads of the closure plugs before inserting and tightening them into the unused outlets.

Maintenance

The BELL Weatherproof Box is designed for minimal maintenance. Periodically inspect the box for any signs of damage, corrosion, or compromised seals. Ensure all conduit connections remain tight and that the box cover (if applicable, sold separately) is securely fastened. Clean the exterior with a damp cloth as needed.

Troubleshooting

• Water Ingress: If water is found inside the box, immediately disconnect power. Inspect all conduit connections, closure plugs, and the box cover for proper sealing. Reapply silicone sealant as necessary.
• Loose Connections: Periodically check all electrical connections within the box to ensure they remain tight and secure.
• Corrosion: While the powder coat finish is designed for resistance, inspect for any signs of corrosion, especially in harsh environments. Address any corrosion promptly to maintain integrity.

Specifications

Warranty and Support

For warranty information and technical support, please refer to the official BELL product website or contact their customer service directly. Keep your purchase receipt for warranty claims.

Manufacturer: Hubbell

UPC: 050169534809