Intermatic RC613 Receiver Instruction Manual

1. Product Overview

The Intermatic RC613 Receiver is a component of a two-part remote control system designed for switching electrical loads. It functions as an ordinary ON/OFF switch but also responds to signals from a handheld transmitter (sold separately). This module is suitable for both indoor and outdoor applications, managing various switching tasks around residential or agricultural settings. Users can activate or deactivate connected loads (such as lights or pumps) remotely using the transmitter or directly via the ON/OFF button on the receiver itself. A single transmitter can control up to three receivers, and each receiver can be programmed with a unique code.

The RC613 model includes a manual ON/OFF button and is intended for installation at the load's location. The RC613L model is identical but features extra-long (36-inch) leads.

2. Features

• Responds to signals from a handheld transmitter for remote control.
• Equipped with an integrated ON/OFF button for local control.
• Designed for versatile indoor and outdoor use.
• Capable of handling various switching applications for connected loads.
• Allows a single transmitter to operate up to three receivers.
• Each receiver can be programmed with a different code for customized control.

3. Important Considerations for Installation and Operation

• Mounting Orientation: The receiver must be mounted upright with the antenna positioned at the top.
• Temperature Sensitivity: Avoid mounting the receiver above heaters, air conditioners, or in direct afternoon sunlight, as radio receivers are sensitive to heat.
• Range Optimization: For optimal range and reliable reception, install the module as high as practically possible above ground level.
• Metal Obstructions: Large metal objects can interfere with radio signals. Do not mount the receiver on metal walls, fences, or near significant metal structures.
• Environmental Factors: Environmental conditions, such as rain, can affect the remote control system's operating range.
• Electrical Interference: Certain electrical equipment, like brush-type motors or electronic gas heater igniters, emit radio signals that can interfere with the receiver. Avoid mounting the module near such equipment.
• Spacing: To prevent electronic interference between modules, install receivers at least 3 feet apart.
• Wireless Range: The open field range is approximately 200 feet or less, varying based on battery age, proximity to large metal objects, receiver location, and environmental conditions.

4. Installation Instructions

Before beginning installation, ensure all power to the circuit is turned off at the breaker. Follow all local electrical codes and safety guidelines.

Figure 1: Intermatic RC613 Receiver. This image shows the receiver unit with its ON/OFF button and wiring connections.

1. Mounting the Receiver: Attach the receiver module to the top of an outdoor-grade junction box. Ensure the entire assembly is raintight.
2. Selecting Location: Choose an appropriate location for installation, considering the "Important Considerations" section above. Install the receiver assembly on a vertical surface or other suitable support using appropriate hardware.
3. Conduit and Wiring: Prepare necessary conduit runs as required by your installation layout and pull in the specified conductors.
4. Wire Connections: Follow the wiring diagram provided with your product. Typically, the White lead connects to the 120V Neutral, the Black lead connects to the 120V Line, and the Red lead connects to the Load. Always verify wire functions with a multimeter if unsure, as wire colors may vary in existing installations.
5. Testing and Securing: Turn on power and test the installation using the ON/OFF button on the receiver module. After successful testing, replace the junction box cover, ensuring the installation is secure and raintight.
6. Transmitter Linking: Refer to the "Operation" section for instructions on linking a transmitter button with the receiver.

5. Operation

5.1 Linking RC939 Transmitter Button with the RC613 Receiver

This procedure outlines how to pair an RC939 transmitter (sold separately) with your RC613 receiver.

1. Clear Existing Codes: Press and hold the blue code set button on the receiver for 15 seconds, then release it. This clears any previously stored codes.
2. Activate Transmitter: Insert a paper clip into the small hole on the bottom right side of the remote transmitter until the red indicator light illuminates. Note: The illuminated LED may be difficult to see in direct sunlight.
3. Initiate Linking on Receiver: Return to the receiver and press and release the blue code set button.
4. Select Transmitter Button: Choose the specific button on the remote transmitter that you wish to link. Slowly press and release this button.
5. First Click Confirmation: After the 7th slow press and release, you should hear the relay inside the receiver click.
6. Subsequent Clicks: Continue to slowly press and release the remote button. The relay should now click approximately every 4th press.
7. Complete Linking: Repeat the slow press and release action until you hear the relay click 3 or 4 more times.
8. Save Code: Press one of the other two buttons on the remote transmitter to save the newly linked code.

5.2 Linking Multiple Transmitters with a Receiver

Up to three different transmitters can control a single RC613 receiver.

1. To link additional transmitters, repeat steps 1 through 4 from the "Linking RC939 Transmitter Button with the RC613 Receiver" section for each new transmitter.

6. Specifications

7. Warranty Information

The Intermatic RC613 Receiver comes with a 1-year warranty from the date of purchase. For detailed terms and conditions, please refer to the official warranty documentation included with your product or contact Intermatic customer support.

8. Customer Support

For technical assistance, troubleshooting, or warranty claims, please contact Intermatic customer support. Visit the official Intermatic website for contact information and additional resources.

Intermatic Official Website: www.intermatic.com