1. Product Overview
The Dodge P2BSC012 Pillow Block Bearing is a robust component designed for industrial power transmission applications. It features a 2-bolt pillow block design with a 3/4 inch bore and a 1-5/16 inch base to center height. This ball bearing unit utilizes a set screw mount for secure shaft attachment and is relubricatable for extended service life. Constructed from cast iron, it includes a single lip contact seal for protection against contaminants. This non-expansion type bearing is suitable for various machinery requiring reliable rotational support.
2. Setup and Installation
Proper installation is crucial for the longevity and performance of your Dodge P2BSC012 Pillow Block Bearing. Follow these general guidelines:
- Preparation: Ensure the mounting surface is clean, flat, and free from burrs or debris. Verify that the shaft is clean, straight, and within specified tolerances.
- Mounting: Position the pillow block bearing on the mounting surface. Align the bearing with the shaft.
- Shaft Insertion: Carefully slide the shaft through the bearing bore. Avoid forcing the shaft, which could damage the bearing.
- Securing: Tighten the mounting bolts evenly to the recommended torque specifications (refer to specific engineering drawings or Dodge installation guides for precise values). Ensure the bearing housing is firmly seated.
- Set Screw Engagement: Secure the bearing to the shaft using the set screws. Tighten the set screws alternately and incrementally to ensure even pressure and prevent shaft damage.
- Alignment: Verify proper alignment of the shaft and bearing with connected components to minimize stress and vibration.
- Initial Lubrication: If the bearing is not pre-lubricated or requires additional grease, apply the recommended lubricant through the grease fitting.
Note: For detailed installation instructions, always consult the official Dodge installation manual specific to your application.
3. Operating Guidelines
Once installed, the Dodge P2BSC012 Pillow Block Bearing is designed for continuous operation within its specified load and speed limits. Adhere to the following guidelines for optimal performance:
- Load Capacity: Do not exceed the bearing's rated dynamic and static load capacities. Overloading can lead to premature failure.
- Speed Limits: Operate the bearing within its maximum permissible speed. Excessive speeds can generate heat and cause damage.
- Temperature Range: Ensure the operating environment temperature remains within the bearing's specified range. Extreme temperatures can affect lubricant performance and material integrity.
- Vibration and Noise: Monitor for unusual vibrations or excessive noise during operation. These can indicate misalignment, insufficient lubrication, or internal damage.
- Contamination: Protect the bearing from dust, dirt, moisture, and other contaminants, which can degrade lubricant and cause wear.
4. Maintenance
Regular maintenance is essential to maximize the service life of your Dodge P2BSC012 Pillow Block Bearing.
Lubrication:
This bearing is relubricatable. The frequency and type of lubricant depend on operating conditions (speed, load, temperature, environment). Generally:
- Use a high-quality lithium-based grease suitable for industrial bearings.
- Apply grease through the fitting until a slight bead appears at the seal, indicating the bearing is adequately filled. Avoid over-greasing.
- Establish a lubrication schedule based on manufacturer recommendations and application severity.
Inspection:
Periodically inspect the bearing and its surroundings:
- Check for signs of wear, corrosion, or damage to the housing.
- Inspect seals for integrity and signs of lubricant leakage or contaminant ingress.
- Verify mounting bolt tightness and ensure the bearing remains securely fastened.
- Listen for unusual noises and feel for excessive heat or vibration during operation.
- Ensure the shaft is clean and free of rust or pitting where it contacts the bearing.
5. Troubleshooting
This section provides common issues and potential solutions for the Dodge P2BSC012 Pillow Block Bearing.
| Problem | Possible Cause | Solution |
|---|---|---|
| Excessive Noise / Vibration |
|
|
| Overheating |
|
|
| Premature Failure |
|
|
6. Technical Specifications
Key specifications for the Dodge P2BSC012 Pillow Block Bearing:
| Feature | Detail |
|---|---|
| Model Number | P2B-SC-012 |
| Brand | Dodge |
| Bearing Type | Ball Bearing |
| Bore Size | 3/4 inch |
| Mounting Type | 2-Bolt Pillow Block |
| Shaft Attachment | Set Screw Mount |
| Base to Center Height | 1-5/16 inches |
| Material | Cast Iron |
| Seal Type | Single Lip Contact |
| Relubricatable | Yes |
| Expansion Type | Non-expansion |
| Minimum Bolt Spacing | 3-3/8 inches |
| Maximum Bolt Spacing | 4-3/16 inches |
| Item Weight | 1.4 Pounds |
| ASIN | B0036785PQ |
| UPC | 782475113811 |
7. Warranty and Support
Dodge products are manufactured to high-quality standards. For specific warranty information regarding your P2BSC012 Pillow Block Bearing, please refer to the documentation provided with your purchase or visit the official Dodge website.
For technical support, replacement parts, or further inquiries, please contact Dodge customer service or an authorized distributor. You can find more information and products from the brand at the Dodge Store on Amazon.
