1. Introduction
This manual provides essential instructions for the proper use, maintenance, and care of your Waring Commercial WSB60ST 16-inch Stainless Steel Immersion Blender Shaft. This shaft is designed as an interchangeable accessory for specific Waring Big Stix immersion blender power units, offering versatility and durability for commercial kitchen environments.
Image 1.1: The Waring Commercial WSB60ST 16-inch Stainless Steel Immersion Blender Shaft. This component is designed for attachment to compatible Waring Big Stix power units.
2. Safety Information
Always observe basic safety precautions when using electrical appliances, especially in a commercial setting. This shaft is an accessory and must be used with a compatible Waring Big Stix immersion blender power unit.
- Read all instructions: Before using the immersion blender shaft, read all operating instructions for the compatible power unit.
- Proper Attachment: Ensure the shaft is securely attached to the power unit before operation.
- Blade Safety: The cutting blade is sharp. Handle with care to prevent injury.
- Liquid Level: Do not immerse the power unit in liquid. Only the shaft is designed for immersion.
- Supervision: Close supervision is necessary when any appliance is used by or near children.
- Maintenance: Perform maintenance and cleaning only when the power unit is unplugged.
3. Package Contents
Verify that all components are present upon unpacking:
- One (1) Waring Commercial WSB60ST 16-Inch Immersion Blender Shaft
4. Setup
The WSB60ST shaft is designed for easy interchangeability with compatible Waring Big Stix immersion blender power units. Compatible models include WSB25X, WSB50, WSB55, WSB60, WSB65, WSB70, and WSBPPW.
- Ensure Power Unit is Off and Unplugged: Before attaching or detaching the shaft, always ensure the immersion blender power unit is switched off and disconnected from the power supply.
- Align and Attach: Align the top of the WSB60ST shaft with the coupling mechanism on the bottom of the power unit. Push the shaft firmly upwards and twist clockwise until it locks securely into place.
- Verify Connection: Gently pull down on the shaft to ensure it is fully engaged and will not detach during operation.
5. Operating Instructions
Once the WSB60ST shaft is securely attached to a compatible Waring Big Stix power unit, you can proceed with blending operations. Refer to your power unit's instruction manual for specific operating procedures, speed controls, and safety guidelines.
- Prepare Ingredients: Place ingredients in a suitable container for blending. Ensure the container is deep enough to accommodate the 16-inch shaft and prevent splashing.
- Immerse Shaft: With the power unit unplugged, immerse the blending end of the shaft into the ingredients before turning on the power. Ensure the liquid level does not exceed the maximum immersion line, if indicated on your power unit.
- Start Blending: Plug in the power unit and select the desired speed setting. Begin blending, moving the shaft gently up and down and around the container to ensure thorough processing.
- Finish Blending: Once blending is complete, turn off the power unit and unplug it from the outlet. Remove the shaft from the ingredients.
6. Maintenance and Cleaning
Proper cleaning and maintenance extend the life of your immersion blender shaft and ensure hygienic operation.
- Disconnect Power: Always unplug the power unit from the electrical outlet before cleaning or performing any maintenance.
- Detach Shaft: Twist the shaft counter-clockwise and pull down to detach it from the power unit.
- Cleaning: The WSB60ST shaft is completely sealed and dishwasher safe. For manual cleaning, wash the shaft thoroughly with warm, soapy water. Use a brush to clean around the blade area carefully. Rinse thoroughly with clean water.
- Drying: Allow the shaft to air dry completely before storage or reattachment.
- Storage: Store the shaft in a clean, dry place.
7. Troubleshooting
If you encounter issues with your WSB60ST immersion blender shaft, consider the following:
- Shaft not attaching securely: Ensure the shaft is aligned correctly with the power unit's coupling and twisted until it locks. Check for any obstructions in the coupling mechanism.
- Poor blending performance: This is typically related to the power unit or the ingredients. Ensure the power unit is functioning correctly and that ingredients are suitable for immersion blending.
- Unusual noise or vibration: Discontinue use immediately. Check for any damage to the shaft or blade. If damage is present, replace the shaft.
For issues not resolved by these steps, contact Waring Commercial customer support.
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | WSB60ST |
| Shaft Length | 16 inches |
| Material | Stainless Steel |
| Compatibility | Waring Big Stix Immersion Blenders (WSB25X, WSB50, WSB55, WSB60, WSB65, WSB70, WSBPPW) |
| Cleaning | Dishwasher Safe |
| Product Dimensions | 16 x 16 x 4.2 inches (approximate, as part of full unit) |
| Item Weight | 2.78 Pounds (approximate) |
9. Warranty and Support
For information regarding warranty coverage, service, or technical support for your Waring Commercial products, please refer to the documentation provided with your original Waring Big Stix immersion blender power unit or visit the official Waring Commercial website. Keep your purchase receipt as proof of purchase for warranty claims.
Manufacturer: Conair LLC Waring Commercial Inc. (BISS)
