1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Leviton 6633-PLW SureSlide 600W Preset Incandescent Dimmer. This device is designed for use with incandescent lighting loads up to 600 watts and supports both single-pole and 3-way wiring configurations. It features a slide control for precise dimming and an on/off rocker switch for convenience.
2. Important Safety Information
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
- This product is for use with incandescent fixtures only. Do not use with LED, CFL, or other non-incandescent lighting unless specifically rated for such use.
- Install in accordance with all national and local electrical codes.
- If you are unsure about any part of these instructions, consult a qualified electrician.
- Do not exceed the maximum wattage rating of 600W.
- Ensure all wire connections are secure.
3. Package Contents
Verify that all components are present before beginning installation:
- Leviton 6633-PLW SureSlide Dimmer
- Mounting Screws
- Wire Connectors (may vary by package)
Figure 1: Leviton SureSlide Dimmer in its retail packaging, showing the dimmer unit and its features.
4. Setup and Installation
Follow these steps carefully for proper installation. If replacing an existing switch, note the wiring configuration before disconnecting.
4.1 Tools Required
- Screwdriver (Phillips and/or Flathead)
- Wire Strippers
- Electrical Tape
- Voltage Tester
4.2 Installation Steps
- Turn Off Power: Locate the circuit breaker or fuse that controls the light fixture you are working on. Turn it OFF. Use a voltage tester to confirm that power is off at the switch box.
- Remove Old Switch: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch.
- Identify Wires:
- Ground Wire: Typically bare copper or green.
- Hot/Line Wire: Carries power from the breaker.
- Load Wire: Carries power to the light fixture.
- Traveler Wires (for 3-way only): Two wires used in 3-way circuits.
- Wire the Dimmer: Connect the wires from the wall box to the dimmer according to the diagram provided with your dimmer or standard wiring practices. Ensure all connections are tight using wire connectors. The Leviton 6633-PLW typically has a green ground wire, a black wire for the common/hot, and two red wires for load/travelers.
- Mount the Dimmer: Gently push the wired dimmer into the wall box. Secure it with the provided mounting screws.
- Install Wallplate: Attach the decorative wallplate (sold separately) over the dimmer.
- Restore Power: Turn the power back ON at the circuit breaker.
Figure 2: Front view of the Leviton SureSlide Dimmer, showing the slide control and on/off rocker switch.
Figure 3: Side view of the Leviton SureSlide Dimmer, illustrating the depth and wiring terminals for installation.
5. Operating Instructions
The Leviton 6633-PLW SureSlide Dimmer offers intuitive control over your incandescent lighting.
- Turning Lights ON/OFF: Press the bottom rocker switch to turn the lights on or off.
- Dimming Control: Move the slide control up to increase light intensity and down to decrease light intensity.
- Preset Feature: The slide control acts as a preset. When you turn the lights off and then back on using the rocker switch, they will return to the last dimmed level set by the slide control.
6. Maintenance
The Leviton SureSlide Dimmer requires minimal maintenance.
- Cleaning: To clean the dimmer, wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
- No User-Serviceable Parts: There are no user-serviceable parts inside the dimmer. Do not attempt to open or repair the unit.
7. Troubleshooting
If you experience issues with your dimmer, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not turn ON. | No power to the dimmer; loose wiring; faulty bulb. | Check circuit breaker. Verify all wire connections are secure. Replace bulb. |
| Lights do not dim. | Incorrect bulb type (non-incandescent); dimmer not wired correctly. | Ensure incandescent bulbs are used. Recheck wiring connections. |
| Lights flicker or hum. | Minimum load not met; incompatible bulb; loose connection. | Ensure total wattage of bulbs meets dimmer's minimum load (if applicable). Try different incandescent bulbs. Check wiring. |
| Dimmer is warm to the touch. | Normal operation; overloaded circuit. | Slight warmth is normal. If excessively hot, reduce load or consult an electrician. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 6633-PLW (also referred to as 6674-10W) |
| Wattage | 600 Watts |
| Voltage | 120 Volts AC, 60Hz |
| Operation Type | Single Pole or 3-Way |
| Switch Style | Slide Switch with On/Off Rocker |
| Load Type | Incandescent |
| Color | White |
| Certifications | UL, CSA |
| Dimensions | Approximately 1.97 x 0.39 x 1.18 inches |
| Item Weight | Approximately 2.4 ounces |
9. Warranty and Support
This Leviton product is covered by a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or visit the official Leviton website.
For technical assistance or further inquiries, please contact Leviton Customer Support:
- Website: www.leviton.com
- Phone: Refer to the Leviton website for regional contact numbers.
