1. Introduction
The Stromberg Carlson FP-1002-R Foam Grip Wrap is designed to enhance grip and comfort on 1-inch diameter rails. This product provides a 12-inch grip surface and can be installed without disassembling the existing rail structure. It is suitable for various applications where improved hand grip is desired on tubular structures.
Figure 1: Stromberg Carlson FP-1002-R Foam Grip Wrap. This image displays the product designed to provide enhanced grip on 1-inch diameter rails.
2. Safety Information
Please read all instructions carefully before installation and use. Failure to follow these instructions may result in improper installation or reduced product effectiveness.
- Ensure the rail surface is clean and dry before applying the grip wrap.
- Do not use this product on rails with a diameter other than 1 inch, as it may not fit correctly or provide adequate grip.
- Keep packaging materials away from children to prevent choking hazards.
- Dispose of all packaging materials responsibly according to local regulations.
3. Package Contents
The Stromberg Carlson FP-1002-R package includes the following:
- 1x Stromberg Carlson FP-1002-R Foam Grip Wrap
- Adhesive tape for securing ends (typically vinyl tape)
4. Setup & Installation
The FP-1002-R Foam Grip Wrap is designed for easy installation without requiring the disassembly of your existing rail. It is suitable for any 1-inch diameter rail.
- Prepare the Rail: Ensure the 1-inch diameter rail where the grip wrap will be applied is clean, dry, and free from any grease, dirt, or debris.
- Position the Wrap: Carefully unroll the foam grip wrap. Align one end of the wrap with the desired starting point on the rail.
- Wrap the Rail: Begin wrapping the foam grip around the rail, ensuring a snug fit and consistent overlap. The wrap should cover approximately 12 inches of the rail length.
- Secure the Ends: Once the desired length is covered, use the provided adhesive tape to secure both ends of the foam grip wrap firmly in place. Wrap the tape tightly around the ends to prevent unraveling.
Note: Some users have reported that standard electrical tape may offer a more durable and long-lasting hold for securing the ends compared to the included vinyl tape, especially in varying weather conditions. Consider this alternative for enhanced longevity.
5. Operation
Once installed, the Stromberg Carlson FP-1002-R Foam Grip Wrap provides an improved, comfortable, and secure gripping surface on your 1-inch diameter rail. Simply use the rail as intended, benefiting from the enhanced grip and reduced slippage.
6. Maintenance
To ensure the longevity and effectiveness of your foam grip wrap, follow these maintenance guidelines:
- Cleaning: Wipe the foam grip wrap with a damp cloth and mild soap as needed. Avoid harsh chemicals or abrasive cleaners, which can damage the foam material.
- Inspection: Periodically inspect the grip wrap for signs of wear, tear, or loosening, especially at the secured ends.
- Re-securing: If the adhesive tape at the ends begins to loosen, re-secure it with new, strong adhesive tape (e.g., electrical tape) to prevent the wrap from unraveling.
- Replacement: If the foam becomes significantly worn, torn, or loses its gripping properties, consider replacing the wrap to maintain safety and comfort.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Grip wrap is slipping or unraveling. | Ends not secured tightly enough; adhesive tape losing its stickiness. | Re-secure the ends with new, strong adhesive tape. Consider using electrical tape for better durability. |
| Grip wrap does not fit snugly. | Rail diameter is not 1 inch; wrap was not applied tightly. | Ensure the rail diameter is exactly 1 inch. Reapply the wrap, ensuring a tighter, more consistent tension during application. |
| Foam material is deteriorating quickly. | Exposure to harsh chemicals or extreme weather; excessive wear. | Avoid using harsh cleaners. Protect the product from prolonged exposure to extreme elements if possible. Replace the wrap if severely damaged. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | FP-1002-R |
| Brand | Stromberg Carlson |
| Item Weight | 3.2 ounces (approx. 90.7 grams) |
| Product Dimensions | 6.1 x 4.7 x 1.3 inches (packaging) |
| Rail Diameter Compatibility | 1 inch |
| Grip Length Provided | 12 inches (approx. 30.5 cm) |
| Installation Method | Wrap-around, no rail disassembly required |
9. Warranty & Support
For specific warranty information regarding the Stromberg Carlson FP-1002-R Foam Grip Wrap, please refer to the documentation included with your purchase or visit the official Stromberg Carlson website. For technical support or inquiries, please contact Stromberg Carlson customer service directly.
Contact information for Stromberg Carlson can typically be found on their official website or product packaging.