1. Product Overview
The Briggs & Stratton 796496 screw is a genuine replacement component designed to maintain the optimal performance and integrity of your outdoor power equipment. This part is manufactured to exact OEM standards, ensuring a precise fit and reliable function within compatible Briggs & Stratton engines.
Using genuine Briggs & Stratton parts helps ensure that your engine operates as intended and complies with applicable emission regulations.
Image 1: The Briggs & Stratton 796496 screw, a genuine replacement part.
2. Compatibility
This Briggs & Stratton 796496 screw is specifically designed to fit most Briggs & Stratton engine models in the 112000, 111000, 11P000, and 114000 series. It is crucial to verify your engine's model number before purchasing and installing any replacement part to ensure proper fitment and function.
Image 2: Important reminder to check your engine's model number for compatibility.
Refer to your equipment's original owner's manual or the engine's identification label for accurate model information.
3. Installation / Replacement
This section outlines the general procedure for replacing a screw in a Briggs & Stratton engine. Specific steps may vary depending on the exact location and function of the screw within your engine model. Always consult your engine's service manual for detailed, model-specific instructions.
Required Tools:
- Appropriate screwdriver or wrench for the screw head type.
- Torque wrench (recommended for precise tightening).
- Safety glasses and gloves.
Procedure:
- Safety First: Ensure the engine is turned off, cooled down, and the spark plug wire is disconnected to prevent accidental starting.
- Locate the Screw: Identify the screw that needs replacement. This screw is often used in muffler assemblies or other engine components.
- Remove Old Screw: Carefully loosen and remove the existing screw using the appropriate tool. If the screw is seized or damaged, use penetrating oil or a screw extractor as needed.
- Inspect Area: Clean any debris or corrosion from the screw hole and surrounding area. Inspect the threads for damage.
- Install New Screw: Insert the new Briggs & Stratton 796496 screw into the designated hole. Hand-tighten first to ensure it threads correctly.
- Tighten to Specifications: Using a torque wrench, tighten the screw to the manufacturer's specified torque settings. Over-tightening can strip threads, while under-tightening can lead to loosening during operation.
- Reconnect and Test: Reconnect the spark plug wire. Start the engine and check for proper operation and secure fitment of the component where the screw was installed.
Note: For muffler bolts, applying a thin coat of high-temperature anti-seize compound to the threads can prevent future seizing, especially when steel bolts are used in aluminum manifolds.
4. Maintenance Considerations
While a screw itself requires minimal maintenance, its proper function is critical to the overall performance and safety of your engine. Consider the following:
- Periodic Inspection: During routine engine maintenance, visually inspect all screws and fasteners for signs of loosening, corrosion, or damage.
- Tightness Check: If a screw appears loose, gently tighten it to the recommended torque specification. Avoid over-tightening.
- Corrosion Prevention: In environments prone to moisture or chemicals, consider applying a suitable anti-corrosion coating or grease to exposed screw heads.
- Genuine Parts: Always use genuine Briggs & Stratton replacement screws to ensure material quality, thread integrity, and proper fit.
5. Specifications
| Attribute | Detail |
|---|---|
| Part Number | 796496 |
| Manufacturer | Briggs & Stratton |
| Compatibility | Most Briggs & Stratton 112000, 111000, 11P000, 114000 series engines |
| Material | (Specific material not provided, assumed to be standard fastener grade) |
| Weight | Approximately 0.634 ounces (18 grams) |
6. Troubleshooting
If you encounter issues after replacing the screw, consider the following:
- Loose Component: If the component secured by the screw is loose, re-check the screw's tightness. Ensure it is torqued to specifications.
- Stripped Threads: If the screw does not tighten properly, the threads in the engine block or component may be stripped. This requires professional repair, such as re-tapping or using a thread repair kit (e.g., Helicoil).
- Incorrect Part: Double-check that the 796496 screw is indeed the correct part for your specific engine model and application.
- Vibration/Noise: Excessive vibration or unusual noise after replacement might indicate improper installation or a loose component. Re-inspect all connections.
7. Warranty and Support
For information regarding the warranty of genuine Briggs & Stratton replacement parts, please refer to the official Briggs & Stratton website or contact their customer support directly. Keep your purchase receipt as proof of purchase.
For further assistance or technical support, visit the official Briggs & Stratton Store on Amazon or their main corporate website.
