Product Overview
The ATD Tools 2114 is a compact 1/4-inch drive air ratchet designed for various applications, particularly in body and engine shops, and for tasks requiring access to confined areas. It features a durable aluminum housing and a black finished head assembly with a tang style forward/reverse knob and a ball-type socket retainer.
Key Features:
- Maximum torque: 25 feet/pounds
- Free speed: 250 rpm
- Average air consumption: 4.2 cfm
- Length: 6.7 inches
Image: The ATD Tools 2114 1/4-inch Drive Air Ratchet, featuring its sleek aluminum body and black ratchet head with a square drive.
Setup
Before operating the air ratchet, ensure you have a clean, dry, and regulated air supply. Proper setup is crucial for optimal performance and tool longevity.
- Air Supply Connection: Connect the air ratchet to an air compressor using a 1/4-inch NPT air inlet. Ensure all connections are secure and leak-free.
- Air Pressure Regulation: Set your air compressor's regulator to the recommended operating pressure, typically around 90 PSI (6.2 bar). Do not exceed the maximum recommended pressure for the tool.
- Lubrication: Before first use and regularly thereafter, apply a few drops of pneumatic tool oil into the air inlet. This lubricates internal components and helps prevent corrosion.
- Hose and Fittings: Use an air hose with an adequate inner diameter (e.g., 3/8-inch) to ensure sufficient airflow to the tool. Check all quick-connect fittings for proper sealing.
Operating Instructions
Follow these steps for safe and effective operation of your ATD Tools air ratchet.
- Socket Attachment: Select the appropriate 1/4-inch drive socket for your fastener. Push the socket firmly onto the square drive anvil until it locks into place with the ball retainer.
- Direction Selection: The tool features a tang style forward/reverse knob. Rotate the knob to select the desired direction (clockwise for tightening, counter-clockwise for loosening).
- Tool Engagement: Place the socket squarely onto the fastener.
- Trigger Operation: Depress the trigger to activate the tool. The speed of the ratchet is controlled by the amount of trigger depression. Release the trigger to stop the tool.
- Safety Precautions: Always wear appropriate eye protection. Ensure the workpiece is stable. Do not over-tighten fasteners; use a torque wrench for final tightening if specific torque values are required. Disconnect the air supply when changing accessories or performing maintenance.
Maintenance
Regular maintenance will extend the life and ensure the consistent performance of your air ratchet.
- Daily Lubrication: Add 5-10 drops of pneumatic tool oil into the air inlet before and after each use, or every few hours of continuous operation.
- Air Filter/Lubricator: If your air system includes an in-line air filter and lubricator, ensure the filter is clean and the lubricator reservoir is filled with pneumatic tool oil.
- Cleaning: Keep the tool clean and free of debris. Wipe down the exterior with a clean cloth. Do not use harsh solvents that could damage the housing.
- Storage: Store the tool in a clean, dry environment when not in use. Disconnect it from the air supply.
- Inspection: Periodically inspect the tool for any signs of wear, damage, or air leaks. Address any issues promptly.
Troubleshooting
If you encounter issues with your air ratchet, refer to the following common troubleshooting steps.
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool not operating or low power | Insufficient air pressure Lack of lubrication Obstructed air inlet Worn internal parts | Check air compressor pressure and regulator setting Add pneumatic tool oil Clear any obstructions from the air inlet Contact qualified service personnel |
| Air leaks from tool | Loose fittings Damaged O-rings or seals | Tighten all air connections Replace worn or damaged seals/O-rings |
| Excessive vibration | Worn bearings Loose components | Contact qualified service personnel for inspection and repair |
Specifications
Detailed technical specifications for the ATD Tools 2114 1/4" Drive Air Ratchet.
| Specification | Value |
|---|---|
| Brand | ATD |
| Model | 2114 |
| Material | Aluminum |
| Item Length | 6.7 Inches |
| Item Weight | 1.3 Pounds |
| Maximum Torque | 25 Foot Pounds |
| Free Speed | 250 rpm |
| Average Air Consumption | 4.2 cfm |
| Operation Mode | Pneumatic |
| Head Style | Fixed Square |
Warranty and Support
For information regarding warranty coverage, service, or technical support for your ATD Tools 2114 Air Ratchet, please refer to the documentation included with your purchase or visit the official ATD Tools website. You may also contact ATD Tools customer service directly for assistance.
It is recommended to keep your purchase receipt as proof of purchase for any warranty claims.
