Schonbek 5080-75 La Scala Empire Chandelier User Manual

1. Introduction

Thank you for choosing the Schonbek 5080-75 La Scala Empire Chandelier. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.

The Schonbek La Scala Empire Chandelier is a handcrafted crystal lighting fixture designed for indoor use. It features a Bronze Umber finish and requires B10-15 type bulbs, 60W maximum (not included).

2. Important Safety Information

• WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing.
• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• This fixture is intended for indoor use only. Do not expose to moisture or extreme temperatures.
• Ensure the mounting surface can support the weight of the chandelier (approximately 40 pounds).
• Use only the specified bulb type (B10-15) and wattage (60W maximum per bulb). Exceeding the maximum wattage can cause overheating and damage to the fixture or create a fire hazard.
• Handle crystal components with care to prevent breakage.
• Keep packaging materials away from children.

3. Package Contents

Carefully unpack all components and inspect for any damage. Keep all packaging materials until you are certain all parts are present and in good condition. If any parts are missing or damaged, do not attempt to assemble or install the fixture. Contact customer support immediately.

Typical package contents include:

• Chandelier Frame (Bronze Umber finish)
• Crystal Components (various shapes and sizes)
• Mounting Hardware (crossbar, screws, wire nuts)
• Chain and Canopy
• Instruction Manual (this document)

Image 1: Schonbek 5080-75 La Scala Empire Chandelier. This image shows the fully assembled chandelier with its bronze umber frame and crystal elements.

4. Setup and Installation

Tools Required (not included): Screwdriver, wire strippers, pliers, electrical tape, ladder, voltage tester.

1. Turn Off Power: Before starting, ensure the power to the junction box is turned off at the circuit breaker or fuse box. Use a voltage tester to confirm the power is off.
2. Prepare Mounting: Attach the mounting crossbar to the junction box using the provided screws. Ensure it is securely fastened and can support the chandelier's weight.
3. Adjust Chain Length: Determine the desired hanging height for your chandelier. Open a link on the chain using pliers and remove excess chain links. Close the link securely.
4. Wire Connections:
   • Connect the bare copper ground wire from the fixture to the ground wire from the junction box (usually green or bare copper) using a wire nut.
   • Connect the ribbed (or white) wire from the fixture to the white (neutral) wire from the junction box using a wire nut.
   • Connect the smooth (or black) wire from the fixture to the black (hot) wire from the junction box using a wire nut.
   • Ensure all connections are secure and covered with electrical tape if necessary.
5. Secure Canopy: Carefully push the wired connections into the junction box. Slide the canopy up the chain and secure it against the ceiling, covering the junction box. Use the provided collar ring or screws to hold it in place.
6. Install Bulbs: Screw in the appropriate B10-15 type bulbs (60W maximum) into the sockets. Do not overtighten.
7. Attach Crystal Components: Following the specific design of the La Scala Empire Chandelier, carefully attach the crystal components to the frame. Refer to any included diagrams for precise placement. Handle crystals by their edges to avoid fingerprints.
8. Restore Power: Once installation is complete and all components are securely in place, restore power at the circuit breaker.

5. Operating Instructions

The Schonbek 5080-75 La Scala Empire Chandelier operates via a standard wall switch connected to the fixture's electrical circuit. Ensure the correct bulbs are installed before operation.

• Turning On/Off: Use the wall switch to turn the chandelier on or off.
• Dimming (Optional): If connected to a compatible dimmer switch and using dimmable bulbs, you can adjust the light intensity. Ensure both the dimmer switch and bulbs are rated for dimming.

6. Maintenance

Regular cleaning will help maintain the beauty and brilliance of your Schonbek chandelier.

• Cleaning the Frame:
  • Turn off the power to the fixture before cleaning.
  • Wipe the metal frame with a soft, dry, lint-free cloth.
  • Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
• Cleaning the Crystals:
  • For light dusting, use a soft, dry cloth or a feather duster.
  • For a more thorough cleaning, gently wipe crystals with a soft cloth dampened with a solution of mild soap and water, or a specialized crystal cleaner.
  • Dry immediately with a clean, lint-free cloth to prevent water spots.
  • Avoid spraying cleaning solutions directly onto the fixture to prevent damage to electrical components.
• Bulb Replacement:
  • Always turn off power to the fixture and allow bulbs to cool before replacing.
  • Unscrew the old bulb and screw in a new B10-15 type bulb (60W maximum).
  • Do not exceed the recommended wattage.

7. Troubleshooting

If you experience issues with your chandelier, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, contact a qualified electrician or Schonbek customer support.

8. Specifications

9. Customer Support

For further assistance, missing parts, or warranty inquiries, please contact Schonbek customer support. Refer to the official Schonbek website or your purchase documentation for contact details.

You can also visit the Schonbek Store on Amazon for more information.