Theater Solutions TS6 Speaker Selector Box Instruction Manual

Introduction

The Theater Solutions TS6 Six Zone Speaker Selector Box is designed to expand your home audio system by allowing you to connect and manage up to six pairs of speakers from a single amplifier or receiver. This unit provides essential impedance protection for your amplifier, ensuring safe operation even when multiple speaker pairs are active simultaneously. Its user-friendly push-button interface allows for individual activation of each speaker zone, providing flexible control over your listening environment.

Key features include:

• Connects up to 6 pairs of speakers (4 to 16 ohm impedance).
• Handles up to 300W RMS per channel.
• Integrated amplifier/receiver impedance protection.
• Accommodates 14 to 22 gauge speaker wire with spring-loaded connectors.
• Durable black steel housing with soft rubber feet.
• Passive design, requiring no external power.

Figure 1: Front view of the TS6 Speaker Selector Box, showing the six zone selection buttons and the 'Single Pair Direct' button.

Safety Instructions

Please read and understand all safety instructions before operating this device. Failure to do so may result in injury or damage to the unit or connected equipment.

• It is recommended that the amplifier/receiver be turned OFF while making any connections.
• Do not use this device where there is a risk that the switcher may come into contact with water or excessive moisture, such as near pools, bathtubs, or in wet basements.
• In the event of a malfunction, do not attempt to service the product yourself. Please contact Theater Solutions customer support for assistance.
• Ensure proper ventilation around the unit to prevent overheating.
• Use only speaker wire of appropriate gauge (14 to 22 gauge) for connections.

Figure 2: Excerpt from the official instruction manual, highlighting important safety guidelines.

Setup and Connections

Setting up your TS6 Speaker Selector Box is straightforward. Follow these steps to connect your amplifier/receiver and speakers:

1. Power Off Equipment: Before making any connections, ensure your amplifier/receiver and all other audio equipment are turned OFF and unplugged from the power outlet.
2. Connect Amplifier/Receiver: Locate the main speaker outputs (Left and Right) on your amplifier or receiver. Connect these outputs to the "L INPUTS R" terminals on the rear of the TS6 Speaker Selector Box using appropriate speaker wire. Ensure correct polarity (+ to + and - to -).
3. Connect Speakers: Connect up to six pairs of speakers to the "OUTPUTS" terminals on the rear of the TS6. Each pair of terminals is labeled for zones 1 through 6. Connect the left speaker of a pair to the 'L' terminal and the right speaker to the 'R' terminal for each zone. Maintain correct polarity for all connections.
4. Secure Connections: The TS6 uses spring-loaded wire connectors. Press down on the tab, insert the stripped end of the speaker wire, and release the tab to secure the connection. Ensure no stray wire strands are touching other terminals, which could cause a short circuit.
5. Placement: Place the TS6 on a stable, flat surface. The soft rubber feet will prevent scratching and provide stability. Ensure adequate ventilation around the unit.

Figure 3: Rear panel of the TS6, illustrating the input terminals for the amplifier/receiver and the six output terminals for speaker zones.

Operating Instructions

Once all connections are made and verified, you can begin using your TS6 Speaker Selector Box.

• Power On: Plug in and power on your amplifier/receiver.
• Zone Selection: To activate a speaker zone, simply press the corresponding numbered button (1 through 6) on the front panel of the TS6. The button will typically depress or light up (if applicable) to indicate the zone is active.
• Multiple Zones: You can engage one, some, or all zones simultaneously. The TS6's impedance protection circuitry ensures your amplifier remains safe regardless of how many zones are active.
• Deactivating Zones: To deactivate a speaker zone, press its corresponding button again. The button will return to its original position, indicating the zone is off.
• Single Pair Direct Feature: The TS6 includes a "SINGLE PAIR DIRECT" button. This feature is designed to bypass the impedance protection circuit when only one pair of speakers is connected and active. Engaging this button can sometimes provide a slightly more direct signal path. Only use this feature when exactly one pair of speakers is active.

Maintenance

The Theater Solutions TS6 Speaker Selector Box requires minimal maintenance to ensure long-lasting performance.

• Cleaning: Use a soft, dry cloth to wipe down the exterior of the unit. Do not use liquid cleaners, aerosols, or harsh chemicals, as these can damage the finish or internal components.
• Ventilation: Ensure that the ventilation openings (if any) are not blocked by dust or debris.
• Connections: Periodically check all speaker wire connections to ensure they are secure and free from corrosion. Loose connections can lead to poor sound quality or potential damage.

Troubleshooting

If you encounter issues with your TS6 Speaker Selector Box, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact Theater Solutions customer support for further assistance.

Specifications

Warranty Information

Specific warranty details for the Theater Solutions TS6 Speaker Selector Box are typically provided with the product at the time of purchase. For comprehensive warranty information, including terms, conditions, and duration, please refer to the documentation included in your product packaging or visit the official Theater Solutions website.

Keep your proof of purchase (receipt or invoice) as it will be required for any warranty claims.

Customer Support

For technical assistance, troubleshooting beyond this manual, or inquiries regarding parts and service, please contact Theater Solutions customer support.

Contact information can typically be found on the manufacturer's official website or within the product packaging. When contacting support, please have your product model number (TS6) and purchase details ready.