Thule Omnistor Awning Support User Manual

1. Introduction

Thank you for choosing the Thule Omnistor Awning Support. This manual provides essential information for the safe and effective use of your product. This support is designed to provide stable and reliable support for your Omnistor awning, ensuring its proper function and longevity. It features a durable plastic construction, designed for easy installation and manual operation.

Please read this manual thoroughly before installation and use, and keep it for future reference.

2. Safety Information

Always prioritize safety when installing and using the awning support. Failure to follow these instructions could result in injury or damage to the product or awning.

• Ensure the awning support is securely attached to both the awning and the ground/mounting surface before applying any load.
• Do not exceed the maximum recommended load for your awning system.
• Regularly inspect the support for any signs of wear, damage, or loose connections. Replace damaged parts immediately.
• Keep children and pets away from the awning area during installation and operation.
• Avoid using the awning in strong winds or heavy rain, even with the support in place, unless the awning is specifically designed for such conditions. Retract the awning in adverse weather.
• Ensure a minimum clearance of 2 meters is available for proper setup and operation of the awning with the support.

3. Package Contents

Verify that all components are present and undamaged before proceeding with installation. The package should contain:

• Thule Omnistor Awning Support (Quantity: 2 pieces, as typically supplied for a pair)

Figure 3.1: Two Thule Omnistor Awning Support units, typically included in a set.

4. Setup and Installation

The Thule Omnistor Awning Support is designed for straightforward assembly and installation, requiring no special tools. Follow these steps for proper setup:

1. Prepare the Awning: Fully extend your Thule Omnistor awning to its desired position. Ensure the area beneath the awning is clear and provides the minimum required clearance of 2 meters.
2. Identify Attachment Points: Locate the designated attachment points on your awning's lead rail or support arms where the Thule Omnistor Awning Support will connect. These are typically slots or channels designed to receive the support.
3. Insert the Support: Gently slide the top end of the awning support into the corresponding slot or channel on the awning. Ensure it clicks or locks securely into place. The design allows for easy insertion and removal.
4. Position the Base: Once the top is secured, position the base of the support on a stable, level surface. If applicable, use the pre-drilled holes in the support base to secure it to the ground or a mounting plate using appropriate fasteners (fasteners not included).
5. Adjust and Verify: Ensure the awning support is vertical and provides adequate tension to the awning. Verify that both supports (if using a pair) are evenly positioned and securely attached.

Figure 4.1: Side view of the awning supports, showing the channel design for attachment.

5. Operating Instructions

The Thule Omnistor Awning Support operates manually and does not require any electrical power.

• Deployment: After extending your awning, attach the supports as described in the "Setup and Installation" section. Ensure they are firmly in place before leaving the awning unattended.
• Retraction: Before retracting your awning, always detach the Thule Omnistor Awning Supports. Gently pull the support out of its attachment point on the awning. Store the supports in a safe place to prevent damage.
• Stability: The supports are designed to enhance the stability of your awning, especially in light to moderate conditions. They are not intended to make the awning resistant to severe weather.

6. Maintenance

Regular maintenance will ensure the longevity and optimal performance of your Thule Omnistor Awning Support.

• Cleaning: Clean the plastic supports periodically with mild soap and water. Avoid abrasive cleaners or solvents that could damage the material.
• Inspection: Before each use, inspect the supports for any cracks, deformities, or signs of wear. Check the attachment points for any damage.
• Storage: When not in use, store the supports in a dry, cool place, away from direct sunlight and extreme temperatures, to prevent material degradation.

7. Troubleshooting

If you encounter issues with your Thule Omnistor Awning Support, refer to the following common problems and solutions:

8. Specifications

• Brand: Thule
• Model Number: 1500601212
• ASIN: B002BW460U
• Material: Durable Plastic (as per product description and images)
• Operation Mode: Manual
• Assembly Required: Yes
• Package Dimensions: 13.2 x 12.2 x 2.6 cm
• Package Weight: 70 g
• Minimum Clearance Required: 2 meters
• Country of Origin: Germany

9. Warranty and Support

For detailed warranty information, please refer to the official Thule website or the warranty card included with your purchase. Thule products are known for their quality and are backed by comprehensive support.

If you require technical assistance, replacement parts, or have questions not covered in this manual, please contact Thule customer service or visit their official website:

Visit the Thule Store on Amazon

Figure 9.1: Thule brand logo.