1. Introduction
The Trimble Recon is a rugged handheld computer designed for outdoor and demanding environments. It features a 200MHz processor, 64MB RAM, 128MB Flash Memory, and a 4000 mAh battery, all operating on Microsoft Windows Mobile 6. Its sunlight-readable VGA display ensures visibility in various lighting conditions. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Trimble Recon device.
Figure 1: Trimble Recon Handheld Computers. This image displays five Trimble Recon devices, showcasing their robust design and form factor, suitable for field use.
2. Setup Guide
2.1 Unpacking and Initial Inspection
Upon receiving your Trimble Recon, carefully unpack all components and inspect for any signs of damage. The complete factory kit includes:
- Trimble Recon PDA unit
- Rechargeable Battery
- USB Cable
- Power Cable (AC Adapter)
- Hand Strap
- Software CD
- Various Accessories/Adapters
- Starter Guide
2.2 Battery Installation and Charging
- Ensure the device is powered off before installing the battery.
- Locate the battery compartment on the rear of the device.
- Insert the 4000 mAh battery, ensuring proper alignment of the contacts.
- Secure the battery compartment cover.
- Connect the power cable to the device and plug the AC adapter into a power outlet.
- Allow the device to charge fully before first use. A full charge typically takes several hours.
2.3 Powering On/Off
- To Power On: Press and hold the power button (usually marked with a circle and a vertical line) until the screen illuminates.
- To Power Off: Press and hold the power button until the power-off options appear on the screen, then select "Power Off" or "Shut Down". Alternatively, a quick press may put the device into sleep mode.
3. Operating Instructions
3.1 Navigating Windows Mobile 6
The Trimble Recon operates on Microsoft Windows Mobile 6. Navigation is primarily done via the touchscreen using the included stylus or your finger, and through the physical navigation buttons.
- Stylus Use: Tap the screen to select items, double-tap to open applications, and drag to scroll.
- Navigation Pad: Use the directional pad (up, down, left, right) to move through menus and options.
- OK/Enter Button: Confirms selections.
- Soft Keys: The buttons directly below the screen often correspond to on-screen labels for specific functions.
3.2 Connecting to a Computer (Syncing Data)
To transfer data between your Trimble Recon and a computer, use the provided USB cable.
- Install the necessary synchronization software (e.g., Microsoft ActiveSync for Windows XP/2000 or Windows Mobile Device Center for Windows Vista/7/8/10) from the included CD or Trimble's official website onto your computer.
- Connect one end of the USB cable to the Trimble Recon and the other end to an available USB port on your computer.
- The synchronization software should automatically detect the device and initiate a partnership or allow for file browsing.
3.3 Using Applications
The Trimble Recon comes pre-loaded with standard Windows Mobile applications. Additional applications can be installed as needed.
- Access applications via the "Start" menu (usually located at the top-left of the screen).
- Tap on an application icon to launch it.
- Refer to specific application documentation for detailed usage instructions.
4. Maintenance
4.1 Cleaning the Device
- Use a soft, lint-free cloth slightly dampened with water or a mild, non-abrasive cleaning solution to clean the screen and casing.
- Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the device's display or finish.
- Ensure all ports are free of dust and debris. Use compressed air if necessary, but do so carefully.
4.2 Battery Care
- To maximize battery life, avoid fully discharging the battery frequently.
- Store the device in a cool, dry place when not in use for extended periods.
- If storing for a long time, charge the battery to approximately 50% before storage.
4.3 Software Updates
Periodically check Trimble's official website for any available software or firmware updates for your Recon device. Keeping the software updated can improve performance and address potential issues.
5. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Low or depleted battery; battery not properly seated. | Charge the battery fully. Ensure the battery is correctly installed. |
| Screen is unresponsive. | Software glitch; screen calibration issue. | Perform a soft reset (refer to starter guide for specific button combination). Recalibrate the screen if the issue persists after reset. |
| Cannot connect to computer. | Incorrect USB cable; driver issues; synchronization software not running. | Ensure you are using the correct USB cable. Reinstall synchronization software and drivers on your computer. Check USB port functionality. |
| Device runs slowly or freezes. | Too many applications running; low memory; software conflict. | Close unnecessary applications. Perform a soft reset. If issues persist, consider a hard reset (data will be lost, back up first). |
6. Specifications
| Feature | Detail |
|---|---|
| Processor | 200MHz |
| RAM | 64MB |
| Flash Memory | 128MB |
| Operating System | Microsoft Windows Mobile 6 |
| Display | Sunlight Readable VGA Display |
| Battery | 4000 mAh |
| Color | Yellow |
| Model Number | RES-VY2BMX-00 |
7. Warranty and Support
The Trimble Recon comes with a full manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your product or visit the official Trimble website.
For technical support, software updates, or additional resources, please visit the official Trimble support portal or contact their customer service. Keep your product's model number (RES-VY2BMX-00) and serial number ready when seeking support.
Official Trimble Website: www.trimble.com
