Important Safety Information
This smoke alarm detects products of combustion using ionization technology. Ionization smoke alarms may detect invisible fire particles (associated with flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. For maximum protection, it is recommended to install both ionization and photoelectric smoke alarms.
- Do not paint the alarm. Paint can clog the sensing chambers and prevent the alarm from operating properly.
- Do not disconnect power. This alarm is designed for continuous operation.
- Test the alarm weekly. Refer to the 'Operation' section for testing instructions.
- Replace the alarm every 10 years. Smoke alarms have a limited lifespan and should be replaced after 10 years from the date of manufacture.
Installation Guide
The Kidde i12060 is a hardwired smoke alarm designed for permanent installation. Ensure power is off at the circuit breaker before beginning installation.
- Prepare Wiring: The alarm comes with a pre-stripped wiring harness with tinned strands for easy connection. Connect the black wire to the hot line, the white wire to neutral, and the orange wire to the interconnect line (if connecting multiple alarms).
- Mount the Base: Secure the mounting bracket to the ceiling or wall using the provided screws. The large mounting base helps cover imperfections and protect surface paint.
- Connect Alarm: Plug the wiring harness into the back of the smoke alarm.
- Attach Alarm to Base: Align the alarm with the mounting bracket and twist clockwise until it locks into place.
- Activate Battery Backup: Remove the battery pull tab to activate the included 9-volt battery backup. This ensures continuous protection during power outages.
- Restore Power and Test: Turn on the power at the circuit breaker and test the alarm as described in the 'Operation' section.
Image: Rear view of the Kidde i12060 smoke alarm, illustrating the mounting plate and the pre-stripped wiring harness for electrical connection.
Image: A person reaching up to install the smoke alarm onto the ceiling mounting bracket, demonstrating the final step of physical installation.
Operation
Once installed and powered, your Kidde i12060 smoke alarm is ready to protect your home. It features an indicator LED and a test/hush button for easy interaction.
Testing the Alarm
It is crucial to test your smoke alarm weekly to ensure proper function.
- Press and hold the 'TEST' button located on the front of the alarm.
- The alarm will sound a loud, pulsating alarm. This indicates the electronic circuitry, horn, and battery are working.
- Release the button. The alarm will stop.
Using the Hush Feature
The 'HUSH' feature temporarily silences nuisance alarms caused by non-emergency situations, such as cooking fumes.
- Press the 'HUSH' button when a nuisance alarm sounds.
- The alarm will be desensitized for approximately seven minutes. During this time, the alarm will chirp every 30 to 40 seconds.
- If smoke is too dense, the hush feature will be overridden, and the alarm will continue to sound.
- The alarm automatically resets at the end of the seven-minute period.
Image: Close-up of the front of the Kidde i12060 smoke alarm, highlighting the 'TEST' and 'HUSH' buttons for operational control.
Maintenance and Battery Replacement
Regular maintenance ensures your smoke alarm remains functional and reliable.
Battery Replacement
The i12060 features a convenient front-loading battery door, allowing you to replace the 9-volt battery without removing the alarm from its mounting bracket.
- Open the front battery door by sliding the latch or pressing the designated area.
- Remove the old 9-volt battery.
- Insert a new 9-volt alkaline battery, ensuring correct polarity.
- Close the battery door securely.
- Test the alarm after replacing the battery.
The alarm will chirp approximately once every 30-40 seconds when the battery is low. Replace the battery immediately when this occurs.
Cleaning Your Alarm
Clean your smoke alarm at least once a year. Use a soft brush or cloth to remove dust from the alarm's cover. Do not use cleaning solvents or spray directly onto the alarm.
Image: The Kidde i12060 smoke alarm with its front battery compartment open, clearly showing the 9-volt battery slot for easy replacement.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Alarm chirps every 30-40 seconds. | Low battery. | Replace the 9-volt battery immediately. |
| Alarm sounds frequently without apparent smoke. | Nuisance alarm (e.g., cooking fumes, steam), dust accumulation. | Use the 'HUSH' feature. Clean the alarm as described in the 'Maintenance' section. Ensure proper placement away from cooking areas or high humidity. |
| Alarm does not sound during test. | No power, dead battery, faulty unit. | Check circuit breaker. Replace battery. If issues persist, replace the alarm. |
| Alarm is over 10 years old. | End of service life. | Replace the entire smoke alarm unit. |
Product Specifications
| Brand | Kidde |
| Model Number | i12060 |
| Power Source | 120 Volts AC (Hardwired) with 9V Battery Backup |
| Sensor Type | Ionization |
| Battery Type | 9-volt Alkaline (included) |
| Compatible Devices | Up to 24 Kidde devices (interconnect system) |
| Dimensions | Approximately 11.9 x 6.3 x 6.2 inches |
| Weight | Approximately 3 pounds |
| Operating Temperature | Up to 100 Degrees Fahrenheit |
Warranty and Support
The Kidde i12060 smoke alarm comes with a 10-year limited warranty, covering defects in material and workmanship from the date of purchase.
For technical support, warranty claims, or further assistance, please refer to the official Kidde website or contact their customer service. You can also find a detailed User Guide in PDF format for additional information:
