Rittal 3383500 Blue e Cooling Unit Instruction Manual

1. Product Overview

The Rittal Blue e Cooling Unit, model 3383500, is a roof-mount industrial cooling solution designed for efficient climate control in various applications. This unit provides 3412 BTU/h cooling capacity and operates on 230V, 1 Phase, 50/60 Hz power. Constructed from carbon steel, its dimensions are 16.4" H x 23.5" W x 18.7" D. It features a dust filter for enhanced performance and reduced maintenance.

Figure 1: Rittal 3383500 Blue e Cooling Unit, front view.

Key Features:

• Cooling Capacity: 3412 BTU/h
• Voltage: 230V, 1 Phase, 50/60 Hz
• Material: Carbon Steel
• Dimensions: 16.4" H x 23.5" W x 18.7" D
• Special Feature: Integrated Dust Filter
• Refrigerant: R-134A
• Noise Level: 62 Decibels

2. Safety Information

Read all safety instructions before installation, operation, or maintenance. Failure to follow these instructions may result in property damage, serious injury, or death.

General Safety Precautions:

• Ensure the unit is properly grounded.
• Disconnect power before performing any service or maintenance.
• Only qualified personnel should install, operate, and maintain this equipment.
• Do not block air intake or exhaust vents.
• Use appropriate personal protective equipment (PPE).

3. Setup and Installation

The Rittal Blue e Cooling Unit is designed for roof-mount installation. Proper installation is crucial for optimal performance and safety.

3.1 Unpacking

Carefully remove the unit from its packaging. Inspect for any shipping damage. Report any damage to the carrier immediately.

3.2 Mounting

1. Identify the designated roof-mount location on the enclosure.
2. Ensure the mounting surface is flat and capable of supporting the unit's weight (approximately 88.2 pounds).
3. Secure the cooling unit using appropriate fasteners, ensuring a tight seal to prevent dust and moisture ingress.

3.3 Electrical Connection

1. Ensure the main power supply is disconnected.
2. Connect the unit to a 230V, 1 Phase, 50/60 Hz power source. Refer to the wiring diagram inside the unit's electrical compartment.
3. Verify all connections are secure and comply with local electrical codes.

3.4 Condensate Drainage

Connect the condensate drain hose to the designated outlet on the unit and route it to an appropriate drainage system. Ensure the hose has a continuous downward slope to prevent water accumulation.

4. Operating Instructions

4.1 Initial Startup

1. After installation, restore power to the unit.
2. The unit's display will illuminate, showing the current internal temperature.
3. Allow the unit to run for a few minutes to stabilize.

4.2 Setting Temperature

Use the control panel buttons (typically up/down arrows) to adjust the desired set point temperature. The unit will automatically maintain this temperature within the enclosure.

4.3 Display Indicators

The digital display shows the current internal temperature. Other indicators may include:

• Operating Mode: Indicates if the unit is actively cooling.
• Alarm: Flashes or illuminates to indicate a fault or warning.

5. Maintenance

Regular maintenance ensures the longevity and efficient operation of your Rittal Blue e Cooling Unit.

5.1 Dust Filter Cleaning/Replacement

The unit is equipped with a dust filter to protect internal components. Inspect the filter regularly (e.g., monthly) and clean or replace as needed.

1. Disconnect power to the unit.
2. Locate the filter cover, typically on the front or side of the unit.
3. Remove the filter. Clean it with compressed air or warm, soapy water. If heavily soiled or damaged, replace it with a genuine Rittal filter.
4. Reinstall the clean/new filter and secure the cover.
5. Restore power.

Figure 2: Example of a Rittal cooling unit, showing access for filter maintenance. Regular cleaning of the dust filter is essential for maintaining cooling efficiency.

5.2 Condensate Drain Inspection

Periodically check the condensate drain hose for blockages or kinks. Ensure proper drainage to prevent water buildup inside the unit or enclosure.

5.3 Heat Exchanger Cleaning

Over time, the heat exchanger fins may accumulate dirt, reducing efficiency. If the fins appear dirty, carefully clean them using a soft brush or compressed air. Avoid bending the fins.

6. Troubleshooting

This section provides solutions to common issues. For problems not listed here, contact Rittal technical support.

7. Specifications

8. Warranty and Support

8.1 Warranty Information

Rittal products are designed for durability and reliability. For specific warranty terms and conditions, please refer to the official Rittal warranty documentation included with your purchase or visit the Rittal website. Warranty coverage typically includes defects in materials and workmanship under normal use.

8.2 Technical Support

For technical assistance, troubleshooting, or spare parts inquiries, please contact Rittal customer service. Have your model number (3383500) and serial number ready when contacting support.

Rittal LLC
Contact information can be found on the official Rittal website or in your product documentation.